Firegear ANF-L48 Page 1 Instructions Manual Download

Page: 1 / 14

AnF “Assemble-n-Finish” Fire Pit Enclosures

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS

DO NOT ATTEMPT TO ASSEMBLE OR INSTALL THIS PRODUCT

Warning:

Outdoor Use Only

INSTALLATION PRECAUTION

These enclosures requires a minimum 18-square inches of cross ventilation per

installed burner. Failure to provide proper ventilation can void the warranty.

ANF-R42

42” x18” enclosure fi ts FPB-16R/19R & FPB-20S

ANF-R48

48”x18” enclosure fi ts FPB19R/25R or FPB20S/26S

ANF-R60

60”x18” enclosure fi ts FPB-25R/29R/33R or FPB26S/32S/38S

ANF-L48

48”x 24”x 18” enclosure fi ts FPB-24L/30L/36L

ANF-L66

66”x24”x18” enclosure fi ts FPB-24L/30L/36L or (2) FPB-24L (end to end)

ANF-L74

74”x 24”x18” enclosure fi ts FPB-24L/30L/36L or (2) FPB-24L or (2) FPB-30L (end to end)

ANF-L90

90”x 24” x 18” enclosure FPB-24L/30L/36L or (2) FPB-24L or (2) FPB-30L (end to end)

or (2) FPB-36L (end to end)

ANF-S48

42”x 42” x 18” enclosure fi ts FPB-19R/25R, FPB-20S/26S

ANF-S60

60”x 60”x 18” enclosure fi ts FPB-25R/29R/33R or FPB-26S/32S/38S

Model

Description

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE

CALIFORNIA PROPOSITION 65

WARNING

This product can expose you to Chromium, which is

known to the state of California to cause cancer

and birth defects or other reproductive harm.

(For more information, go to www.p65warnings.ca.gov)

Summary of Contents for ANF-L48















Search results

Summary of Contents for ANF-L48

Reviews:

Related manuals for ANF-L48

Brands by name

Popular brands

Firegear ANF-L48, Instructions Manual

Search results

Summary of Contents for ANF-L48

Reviews:

Related manuals for ANF-L48

Brands by name

Popular brands