Pacific energy SUPER INSERT DESIGN-E SPNE Installation And Operating Instructions Manual Download

Page: 1 / 24

050515-24 SPNE

5055.101.B

MODEL:
SUPER INSERT
DESIGN-E
SPNE

SAFETY NOTICE

If this stove is not properly installed, a house

fi re may result. For your safety, follow the

installation directions. Consult local building

inspector or officials about restrictions and

installation inspection requirements in your

area.

Super Insert

IMPORTANT:

THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER
SAVE THESE INSTRUCTIONS

INSTALLATION

AND OPERATING

INSTRUCTIONS

TESTED and LISTED
to ULC S628 / UL 1482

Meets the U.S. Environmental Protection
Agency's May 2015 Particulate Emission
Standards

SERIAL #

©PACIFIC ENERGY FIREPLACE
PRODUCTS LTD. - 2014

Summary of Contents for SUPER INSERT DESIGN-E SPNE

























Search results

Summary of Contents for SUPER INSERT DESIGN-E SPNE

Reviews:

Related manuals for SUPER INSERT DESIGN-E SPNE

Brands by name

Popular brands

Pacific energy SUPER INSERT DESIGN-E SPNE, Installation And Operating Instructions Manual

Search results

Summary of Contents for SUPER INSERT DESIGN-E SPNE

Reviews:

Related manuals for SUPER INSERT DESIGN-E SPNE

Brands by name

Popular brands