Fire-Lite Alarms MS-4412B Instruction Manual Download Page 38

Page: 38 / 52

Appendix B: NFPA Standard-Specific Requirements

Digital Alarm Communicator/Transmitter - Noti-Fire 911AC

MS-4412B/MS-4424B Instruction Manual PN 15125:G1 10/22/02

Digital Alarm Communicator/Transmitter - Noti-Fire 911AC

Note:

This application is not FM approved

Using the Noti-Fire 911AC DACT for connection to a Central Station Receiver or Protected Premises
Receiving Unit.

• AC Wiring for DACT/FACP must be connected to the same circuit.
• If the unit is not mounted in the control panel’s backbox all connections must be in conduit, less

than 20 ft. (609.6 cm) in length in the same room.

• For additional information refer to the Noti-Fire 911AC Instruction manual.

Figure 23 DACT Connections

+
–

TB3

TB4

OPT1

IN #2

B+ B–

IN #3

B+ B–

IN #4

B+ B–

SUPV 1 SUPV 2

JP1

TB1

LATCH

DISABLE

STD DACT

MS44

B-91

c.cd

Place jumper over pins as shown when employing
a DACT. This directs the control panel to transmit
all trouble conditions except AC LOSS.

To Central
Station

PS 1270

12Volt

7AH Battery

To AC Power

See Below for Terminal
Connections

Control Panel

To Common
Terminal of Relay

Jumper

4XZMF Zone
Relay Module

Summary of Contents for MS-4412B





















































Search results

Summary of Contents for MS-4412B

Reviews:

Related manuals for MS-4412B

Brands by name

Popular brands

Fire-Lite Alarms MS-4412B, Instruction Manual

Search results

Summary of Contents for MS-4412B

Reviews:

Related manuals for MS-4412B

Brands by name

Popular brands