manualshive.com logo in svg

Fire-Lite Alarms MS-4412B, Instruction Manual

The Fire-Lite Alarms MS-4412B user manual, available for free download on our website, is an essential resource for ensuring optimal operation and safety. This comprehensive manual provides step-by-step instructions and valuable insights on maximizing the performance of your Fire-Lite Alarms MS-4412B. Get your free copy now at manualshive.com.

Share
Download
background image

2. Installation

Power-limited Wiring Requirements

16

MS-4412B/MS-4424B Instruction Manual  PN 15125:G1  10/22/02

24 Volt Connections 

Connect the battery cable (p/n 75202) to terminal J9 on the main circuit board using the plug-in connector 
provided. Connect red wire to positive (+) terminal and black wire to negative (–) terminal on opposing 
batteries. Do NOT connect battery interconnect wire at this time.

12 Volt Connections 

Connect the battery cable (p/n 75202) to terminal J9 on the main circuit board using the plug-in connector 
provided. The short cable (battery interconnect) may be removed from bundle. Do NOT connect cables 
to battery at this time.  

Figure 4  Battery Installation and Connection

Power-limited Wiring Requirements 

Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-
limited circuit wiring must remain at least 0.25 in (6.35 mm) away from any nonpower-limited circuit 
wiring. Furthermore, all power-limited circuit wiring and nonpower-limited circuit wiring must pass 
through separate knockouts and/or conduits.   

Figure 5  Power-limited Wiring Requirements

J9

TB1

J9

TB1

MS

44

B-

BA

Tc

on

n.cd

r

24 Volt 

Connections

12 Volt 

Connections

TONE

SILENCE

ALARM

SILENCE

ALARM

ACTIVATE

SYSTEM

RESET

AC POWER

SYSTEM

ALARM

ALARM TEST

SUPERVISORY

SYSTEM

TROUBLE

CIRCUIT

TROUBLE

ALARM

SILENCED

POWER

TROUBLE

ZONE 1

ZONE 2

ZONE 3

ZONE 4

SW1

TB2

TB3

TB4

OPT1

OPT2

J9

J1

JP12

TB1

OUT#1

B+   B–

OUT#2

B+   B–

ALARM

NO  NC  C

IN #2

B+ B–

IN #3

B+ B–

IN #4

B+ B–

SU PV 1 SU PV 2

JP1

TB1

LATCH

DISABLE

J2

Power-limited 
Circuit

Nonpower-limited 
Circuit

All upper terminals are power-limited circuits

Power-limited 
Circuit

M

S

44B

-p

lw

ir

ing

.cdr

Summary of Contents for MS-4412B





















































Reviews:

No comments

Related manuals for MS-4412B

Wavetec Spectra Installation Manual preview
Spectra
Brand: Wavetec Pages: 17
Calsense ET1 Manual To Programming preview
ET1
Brand: Calsense Pages: 9
MaestroHome Smart Controller Quick Setup Manual preview
Smart Controller
Brand: MaestroHome Pages: 10
Hanna Instruments HI 8001 Instruction Manual preview
HI 8001
Brand: Hanna Instruments Pages: 88
Veeder-Root TLS Install, Setup, & Operation Manual preview
TLS
Brand: Veeder-Root Pages: 27
Valve Concepts 1078 Installation, Operation And Maintenance Manual preview
1078
Brand: Valve Concepts Pages: 18
K&K M1500 Installation Instructions Manual preview
M1500
Brand: K&K Pages: 6
Ascon tecnologic Y39 Operating Instructions Manual preview
Y39
Brand: Ascon tecnologic Pages: 16
KIOUR FA3F Quick Start Manual preview
FA3F
Brand: KIOUR Pages: 3
Topway HMT028ATB-C User Manual preview
HMT028ATB-C
Brand: Topway Pages: 14
Wave Home Solutions WV-SCBT Installer Manual preview
WV-SCBT
Brand: Wave Home Solutions Pages: 15
I-Tork PDS Series Installation & Operation Manual preview
PDS Series
Brand: I-Tork Pages: 15
MGC RAXN-LCD Installation And Wiring Manual preview
RAXN-LCD
Brand: MGC Pages: 16
HEIDENHAIN ND 1300 Operating Instructions Manual preview
ND 1300
Brand: HEIDENHAIN Pages: 257
Carel DPWL Series Quick Start Manual preview
DPWL Series
Brand: Carel Pages: 2
R-Tec controlR Installation Manual & User Manual preview
controlR
Brand: R-Tec Pages: 14
FAAC B614 Translation Of The Original Instructions preview
B614
Brand: FAAC Pages: 63
Haiwell S04AI User Manual & Application Case preview
S04AI
Brand: Haiwell Pages: 18

Brands by name

Popular brands

Load more brands