Fire-Lite Alarms MS-4412B Instruction Manual Download Page 44 | Manualshive

Page: 44 / 52

background image

Appendix C: Testing & Maintenance

Troubleshooting

44

MS-4412B/MS-4424B Instruction Manual PN 15125:G1 10/22/02

Table 3 Troubleshooting Table

Symptom

Problem

Solution

AC
Power
LED ON

System trouble
LED ON

Circuit trouble
LED ON

Notification appliance circuit
trouble

1. Check TB3 for proper connections.
2. Remove all field wiring and install dummy ELR at
output circuit. Check for supervisory voltage across it,
(Normal -2.3 V), if problem persists, replace circuit
board.
3. Removed dummy ELR, reconnect field wiring and
measure voltage across output; (trouble-5V, short 0V).
4. Check for ELR at last device.
5. Check field wiring.

Any of the right
column yellow
LEDs flashing

Initiating zone open circuit
trouble

1. Check TB4 for proper connections.
2. Remove field wiring for zone in trouble and install
dummy ELR (4.7K for 24V; 2.2K for 12V). If
problem persists, replace circuit board.
3. Check for ELR at last device.
4. Check field wiring.

Any of the right
column yellow
LEDs steady
ON

Zone disable

1. Check installation manual.

Power trouble
LED ON

Battery trouble
Batt yellow
LED ON

Missing or
Disconnected

1. Check battery connections.

Low or
damaged
battery

1. Remove batteries, check voltage across charger
output (17 to 19V for 24V; 8-10V for 12V), otherwise
replace circuit board.
2. Reconnect batteries, measure battery voltage at
battery terminals. If voltage is less than 85% of rated
voltage, allow them to charge for 48 hours.
3. If problem persists, replace batteries.

Ground fault trouble
Earth yellow LED ON

1. Remove field wiring from main panel and optional
module(s) (if installed). Install dummy ELR (4.7K for
24V; 2.2K for 12V).
2. Remove both battery leads.
3. If trouble clears, connect one circuit at the time to
pin point the problem.
4. If trouble doesn’t clear, replace circuit board.

Yellow LED on
4XTMF ON

4XTMF (4412TM)

1. Move Municipal Box disconnect switch SW1 up.

OPT1, OPT2 jumper cut

1. Install optional module(s) or replace jumper if
module(s) is not used.

Municipal Box open circuit

1. Install dummy load if Municipal Box option isn’t
used.
2. Check Municipal Box wiring.

Any of the right column red LEDs
ON

Short on initiating circuit wiring

1. Remove field wiring and install ELR. If trouble
clears, look for faulty or incorrectly wired devices.

Disconnecting Municipal Box
switch ON 4XTMF (4412TM)
does not create a trouble

Jumper for optional modules
isn’t cut

1. Cut associated jumper OPT1 or OPT2.

4XZMF(4412ZM): associated
LED doesn’t activate for alarm,
trouble or supervisory conditions

Optional module trouble

1. Make sure module is properly installed.
2. Move disable switch SW1 on 4XZMF (4412ZM) to
the left.

RZA-4XF piezo doesn’t sound for
alarm, trouble or supervisory
conditions

4XLMF

(4412LM)

1. Make sure that 4XLMF (4412LM) module is
installed on J8.
2. Check field wiring.

Micro Fail yellow LED ON

Microprocessor damaged

1. Replace circuit board.

All RZA-4XF LEDs stay ON

Power wasn’t removed prior to
installation

1. Press system reset.

AC
Power
LED OFF

System trouble LED ON

Loss of main power

1. Check incoming power (TB1).

Damaged circuit breaker

1. Replace circuit board.

Micro Fail yellow LED ON

Microprocessor damaged

1. Replace circuit board.

«
...
42
43
44
45
46
...
»

Summary of Contents for MS-4412B





















































Reviews:

No comments

Related manuals for MS-4412B

Brand: Jafar Pages: 10

Brand: Jafar Pages: 8

Brand: Caen Pages: 20

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Saga Pages: 9

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 340

Brand: ETC Pages: 8

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brand: Grundfos Pages: 16

Brand: Loewe Pages: 62

Brand: Shimaden Pages: 32

Devicenet R7F4HD-DAC32C

Brand: M-system Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands