Fire-Lite Alarms MS-4412B Instruction Manual Download Page 10 | Manualshive

Page: 10 / 52

background image

1. Product Description

DIP Switch Functions

10

MS-4412B/MS-4424B Instruction Manual PN 15125:G1 10/22/02

DIP Switch Functions

The table below describes the DIP switch functions. For a more detailed explaination see "Setting Mode
of Operation" on page 27.

Options

Three optional modules are available for use on the control panel. The control panel provides mounting
slots for two of these optional module boards.

Transmitter Module - 4XTMF (12V: 4412TM)

The Transmitter Module provides a supervised output for a Local Energy
Municipal Box transmitter and alarm and trouble reverse polarity circuits for
Remote Station Service. Also included is a DISABLE switch and disable
trouble LED.

Note:

As a jumper option, the alarm reverse polarity circuit will open on trouble if no

alarm exists.

Specifications for Local Energy Municipal Box service

(NFPA 72 Auxiliary

Fire Alarm System)

Supervisory current: 5.0 mA.
Trip current: 0.35 amps (subtracted from Notification Appliance power).
Coil Voltage: 3.65 VDC.
Coil resistance: 14.6 ohms.
Maximum allowable wire resistance between panel and trip coil: 3 ohms.
Municipal Box wiring can leave the building.

Specifications for Remote Station Service

(NFPA 72 Remote Station Fire Alarm System)

Maximum load for each circuit: 10 mA.
Reverse polarity output voltage: 12 or 24 VDC.
Remote Alarm and Remote Trouble wiring can leave the building.

#1

Alarm
Verification

ON Alarm Verification enabled (two-minute period).
OFF No verification employed.

#2

Waterflow

ON Zone 3 configured for Waterflow.
OFF Zone 3 functions as a normal Initiating Device Circuit.

#3

Supervisory

ON Zone 4 configured for Supervisory.
OFF Zone 4 functions as a normal Initiating Device Circuit.

#4

Silence
Inhibit

ON Alarm Silence will not function for 60 seconds after initiation of an alarm.
OFF Alarm Silence is possible at any time after initiation of an alarm.

#5

Disable
NACs

ON Two Notification Appliance Circuits and the Alarm Relay are disabled.
OFF Two Notification Appliance Circuits and the Alarm Relay are enabled.

#6

Walk Test

ON Places the panel into Walk Test Mode.
OFF Normal Operating Mode.

Note:

See “Setting Mode of Operation” on page 27 for a more detailed explanation of DIP switch functions.

TB1

TBL

J1

J2

4XTMF

.cd

r

«
...
8
9
10
11
12
...
»

Summary of Contents for MS-4412B





















































Reviews:

No comments

Related manuals for MS-4412B

Brand: Jafar Pages: 9

Brand: Jandy Pages: 28

Brand: Jands Pages: 6

Brand: Parkside Pages: 86

Brand: YUGE Pages: 69

Brand: Quectel Pages: 232

Brand: Quectel Pages: 9

Brand: Quectel Pages: 73

Brand: Rain Bird Pages: 4

Brand: Rain Bird Pages: 2

Brand: Rain Bird Pages: 140

WeatherSmart RSC600i

Brand: Raindrip Pages: 36

Brand: Automated Logic Pages: 10

Brand: Heat & Cool Pages: 5

Brand: Zencontrol Pages: 2

Brand: Gasboy Pages: 119

Brand: IMG STAGELINE Pages: 14

Brand: VAT Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands