Finn HydroSeeder T170 ML Operator Instructions And Parts Manual Download Page 12 | Manualshive

Page: 12 / 95

background image

6

OPERATION AND MAINTENANCE MANUAL

FOR FINN T170 HYDROSEEDERS

®

This manual provides instructions for the operation and maintenance of the FINN T170
HydroSeeder

®

. For best results and to ensure longer life of the equipment, please follow these

instructions carefully. For your safety, read the entire manual before operating this unit.

DEFINITION OF HYDROSEEDING

Hydroseeding is the process whereby seed, fertilizer and/or lime, and wood fiber mulch (using
water as a carrying medium) are applied on the soil to establish vegetation.

THE FINN HYDROSEEDER

®

AND HOW IT WORKS

The FINN HydroSeeder

®

will apply seed, fertilizer and/or lime, wood fiber mulch, or stabilizing

materials in any prescribed or desired combination. The materials placed in the HydroSeeder

®

slurry tank are mixed with water and kept in suspension by a dual agitation process, recirculation
of slurry and mechanical agitation, thus forming a slurry that is pumped to the discharge
assembly and directed onto the seed bed by the operator. This equipment is designed to
accomplish hydroseeding in one easy operation with maximum efficiency.

MOUNTING THE HYDROSEEDER

®

For speed and mobility of operation, the HydroSeeder

®

should be mounted on a truck or trailer.

However, it is important to select a carrier with sufficient capacity to handle the added weight.

HYDROSEEDER

®

MOUNTING INFORMATION

C

Distance from HydroSeeder

®

front to center of

gravity

OAL

Overall length of the HydroSeeder

®

HW

HydroSeeder

®

weight

*

Weight of HydroSeeder

®

, water, and full charge

of granular solids only. No auxiliary equipment
or loads included.

T170

English

Metric

C

(loaded)

71.5 in.

181.6 cm

C

(empty)

97.0 in.

246.4 cm

OAL

198.0 in.

502.9 cm

HW

(empty)

6766 lbs.

3,069 kg

HW

(water only)

21,379 lbs.

9,697 kg

HW

(full load)*

24,291 lbs.

11,018 kg

Figure 1 – Mounting Information Visual Guide

OAL

C

HW

«
...
10
11
12
13
14
...
»

Summary of Contents for HydroSeeder T170 ML
































































































Reviews:

No comments

Related manuals for HydroSeeder T170 ML

Brand: Makita Pages: 10

Brand: Nakayama Pages: 37

Brand: Parker Pages: 39

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Jacto Pages: 64

Brand: QRS Pages: 16

Brand: QMAXZ Lighting Pages: 36

APT-9411 Series

Brand: TAKAYA Pages: 77

Brand: Tadano Pages: 402

Brand: Zimmer Pages: 54

Brand: Zimmer Pages: 4

Brand: Zimmer Biomet Pages: 23

Brand: Zimmer Pages: 16

Brand: Zimmer Pages: 2

Brand: Zimmer Pages: 32

Brand: Zimmer Pages: 96

Brand: Grange Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands