Finn HydroSeeder T170 ML Operator Instructions And Parts Manual Download Page 21 | Manualshive

Page: 21 / 95

background image

15

MAIN MENU ACCESS

To access the Main Menu, press any of the three navigation buttons. The unit will display a
softkey popup window defining the available navigation possibilities. Select the Main Menu using
the center softkey as shown.

MAIN MENU NAVIGATION

Access the main menu using the center softkey. The main
menu will be displayed along with the main menu softkey popup
window. Navigate through the main menu selections by using
the “ ” key. When the desired menu item is highlighted, press
the “

” key to select the menu item. To exit the main menu and

return to the data displays press the EXIT “ ” softkey.

CHANGING PARAMETER SETTINGS

Parameter settings can be changed in one of two ways: using
the “

” / “

” softkeys to increase or decrease a numeric value

or using the Change “ ” softkey to toggle through a list of
programmed settings.

«
...
19
20
21
22
23
...
»

Summary of Contents for HydroSeeder T170 ML
































































































Reviews:

No comments

Related manuals for HydroSeeder T170 ML

Brand: DARAY Pages: 28

Brand: MacDon Pages: 88

Brand: Jiffy Pages: 15

Brand: Makita Pages: 84

Brand: Tascam Pages: 8

Brand: B-K lighting Pages: 5

Brand: B-K lighting Pages: 4

Brand: B-K lighting Pages: 3

Brand: Hagerman Pages: 4

Brand: hager Pages: 2

TECSHOW QUAD SPIDER 60

Brand: Ampro Pages: 9

Brand: Hantek Pages: 124

Brand: Hameg Pages: 10

Brand: NEILPRYDE Pages: 55

Brand: HANYOUNGNUX Pages: 4

Brand: Park House Healthcare Pages: 6

Brand: J&M Pages: 33

Brand: Palmer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands