Finn HydroSeeder T170 ML Operator Instructions And Parts Manual Download

Page: 51 / 95

FINN T170 HYDROSEEDER

TECHNICAL SPECIFICATIONS

POWER ..................................................Cummins QSF 2.8 L Diesel, Tier 4F, 65 hp (48kW), with

over-center clutch. Vibration isolated.

Controls include: clutch, agitator direction and speed, discharge

boom and recirculation control valves, engine throttle, safety

horn and engine start/stop

ENGINE SAFETY SYSTEM ...................Low oil pressure, Electronic Engine Control and Monitoring

TANK

SIZE

..............................................1,750 gallon (6,625 L) liquid capacity

1,500 gallon (5,678 L) working capacity

FUEL TANK CAPACITY ..........................38 gallon (145 L)

PUMP ......................................................Centrifugal 4 in. x 2 in. (10.2 cm x 5 cm) 320 GPM @ 115 psi

(1,210 LPM @ 792 kPa), 1 in. (2.54 cm) solid clearance

PUMP

DRIVE

..........................................Direct drive with over center clutch, pump drive is independent

agitator

operation

AGITATION .............................................Mechanical paddle agitation and liquid recirculation

AGITATOR DRIVE ..................................Reversible, variable speed hydraulic motor drive (0–130 RPM)

DISCHARGE

DISTANCE

........................Up to 200 ft. (61 m) from discharge tower

MATERIAL CAPACITY ............................5,000 lbs. (2,268 kg) granular solids

750 lbs. (340 kg) fiber mulch

NOZZLES ...............................................(2) narrow fan, (2) wide fan, (2) long distance

EMPTY WEIGHT ....................................6,770 lbs (3,071 kg)

WORKING

WEIGHT*

..............................24,300 lbs (11,022 kg)

GVWR .....................................................15,000 lbs (6,804 kg)

* Working weights are approximate and do not include options or stored materials.
Working weights are based on material at 750 lbs./cu. yd.

Summary of Contents for HydroSeeder T170 ML
































































































Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands

Finn HydroSeeder T170 ML, Operator Instructions And Parts Manual

Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands