Finn HydroSeeder T170 ML Operator Instructions And Parts Manual Download Page 42

Page: 42 / 95

Troubleshooting Chart

Symptom

Probable Cause

Suggested Solutions

LEAKS

Tank Bearing

Lack of lubrication - seal worn. Replace seal and follow lube

schedule.

Bolts not tightened.

Tighten uniformly to
25 lb-ft (34 N•m).

Pressure Pipe Clamps

Rubber seal cracked, pinched,
torn or missing.

Replace, always grease seal
before clamping shut.

Suction Pipe Clamps

Rubber seal cracked, pinched,
torn or missing.

Replace, always grease seal
before clamping shut.

Discharge Swivels

Not greased often enough.

Rebuild swivels with repair kit (part
number 012397, qty. 2 required).

Pump Shaft

Pressure lubricator not
serviced.

Replace pump seal. Service
automatic pressure lubricator daily.
See EQUIPMENT CHECK section.

Pump Suction Cover

O-ring cracked, pinched, torn
or missing.

Replace O-ring; use grease when
replacing.

Discharge Boom or
Nozzle Camlock Fittings

Worn or no gasket.

Replace gasket.

MACHINE JUMPS DURING OPERATION

Agitator

Agitator shaft bent by heavy
object falling on it.

Straighten agitator or shim so it
runs true.

Bent Paddles

Loading wood fiber mulch into
tank before tank is half full.

Straighten agitator paddle; realign
agitator to run true.

FOAMING OF SOLUTION AND LACK OF DISTANCE

Pump loses prime -
lacks distance - leaves
excessive amount in
tank - 100 gal (378 L) or
more

Sucking air in suction lines.

Check all suction connections to
ensure that rubber seals are in
good shape. Grease seals before
replacing clamps.

Air entrainment.

See TROUBLESHOOTING YOUR
HYDROSEEDER

Low engine RPM
(Below 2,500 RPM - No load).

See authorized engine dealer.

Soft water.

Slow the agitator.

Too much agitation.

Slow the agitator.

Pump worn.

Reset pump tolerance. See
CLUMP MAINTENANCE section.

Suction partially plugged.

Clean out machine. See
CLEANING AND MAINTENANCE
section.

Nozzle worn or plugged.

Clean nozzles; replace if
necessary.

Fertilizer

Change type.

Clutch sliping due to wear.

Readjust clutch; See clutch
manual.

Summary of Contents for HydroSeeder T170 ML
































































































Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands

Finn HydroSeeder T170 ML, Operator Instructions And Parts Manual

Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands