Finn HydroSeeder T170 ML Operator Instructions And Parts Manual Download Page 13

Page: 13 / 95

A BODY GUIDE OF HEAVY ANGLE, SHOULD BE BOLTED

OR WELDED TO THE HYDROSEEDER® LEG NEAR THE

FRONT END OF THE TANK. IT SHOULD EXTEND BELOW

THE LEG AND CONTACT WEAR PLATE BOLTED TO THE

FRAME SIDE RAIL. THIS GUIDE RESTRICTS LATERAL

MOVEMENT OF TANK & THUS RELIEVES SHEAR STRESS

ON MOUNTINGS.

SHIMS MAY BE REQUIRED FOR

PROPER ALIGNMENT OF GUIDE

PLATE TO WEAR PLATE.

SLOTTED ANGLE ON TOP

WITH 1/2” THICK COVER

STRAP

MOUNTING

KIT

#011562

3/16” GAP

3/8” x 6” WIDE MIN.-

WELD SECURELY TO

HYDROSEEDER®. BOLT

TO TRUCK CHASSIS.

IMPORTANT:

INSURE THAT TUBES

ARE INSERTED TO PRE-

VENT FULL COMPRES-

SION OF SPRINGS WHEN

BOLTS ARE TIGHTENED.

5/8” GRADE 8 BOLT &

NUTS. - ALL PLACES.

WARNING:

DO NOT WELD OR DRILL

TRUCK FRAME IN THIS AREA.

FULL LENGTH SPACER THICK

ENOUGH TO COVER RIVET

HEADS; DRILL CLEARANCE

HOLES FOR RIVET HEADS

WHERE NEEDED.

GENERAL MOUNTING GUIDELINES

Figure 2 – General Truck Mounting Guidelines

Once the proper carrier has been selected, the HydroSeeder

must be securely mounted to it.

Your FINN HydroSeeder

should be mounted by a qualifi ed truck body

installer. Failure to comply could result in minor personal injury or

product or property damage.

Mounting the HydroSeeder

to the truck must allow for tire clearance

and frame twist. Place hard wood spacers along the length of truck

rails or use FINN spring mounting kit (part number 011562) or equivalent.

Summary of Contents for HydroSeeder T170 ML
































































































Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands

Finn HydroSeeder T170 ML, Operator Instructions And Parts Manual

Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands