Finn HydroSeeder T170 ML Operator Instructions And Parts Manual Download Page 5

Page: 5 / 95

HydroSeeder

is a registered trademark of the FINN Corporation

Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
HydroSeeder

Safety Summary Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5

Operation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 46

Definition of HydroSeeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

The FINN HydroSeeder

and How It Works . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mounting the HydroSeeder

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

HydroSeeder

Mounting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

General Mounting Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pre-Start Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Equipment Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Two-Valve Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11

1. Discharge Through Boom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2. Extension Hose Through Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3. Extension Hose or Hose Reel Through Remote Port . . . . . . . . . . .11

Control Panel Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 22

Starting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Area Coverage - Material Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 - 24

Tank Capacity Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 - 29

Prior to Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Discharge Nozzle Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Application of Slurry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 - 32

I. General Application Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

II. Discharge Through the Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

III. Procedures When Using Hoses . . . . . . . . . . . . . . . . . . . . . . . . . 31 - 32

A. Pump Take-Off System or Hose Reel with Remote Valve . . . . 31

B. Extension Hose System without Remote Valve . . . . . . . . . . . . 32

C. Hose Work with Radio Remote . . . . . . . . . . . . . . . . . . . . . . . . . 32

Reloading Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Liming With the HydroSeeder

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Troubleshooting

Your

HydroSeeder

. . . . . . . . . . . . . . . . . . . . . . . . . . . 34 - 37

Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 - 39

After First 4 to 8 Hours of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Daily. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Weekly or Every 40 Hours of Operation . . . . . . . . . . . . . . . . . . . . . . . . . 39

Seasonal and Winter Storage Maintenance . . . . . . . . . . . . . . . . . . . . . . 39

Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Machine Lubrication Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Lubrication and Fluids Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

INDEX

Continued to next page.

Summary of Contents for HydroSeeder T170 ML
































































































Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands

Finn HydroSeeder T170 ML, Operator Instructions And Parts Manual

Search results

Summary of Contents for HydroSeeder T170 ML

Reviews:

Related manuals for HydroSeeder T170 ML

Brands by name

Popular brands