manualshive.com logo in svg

Festool VS-600, Instruction Manual

Share
Download
Festool VS-600 Instruction Manual Download Page 33

 

Position the template on top of 
these two and clamp it down. 
 
Set your router depth of cut to 
the factory specified 12mm for 
the SZ-14 and 15mm for the 
SZ-20. Festool routers are easy 
to adjust by zeroing the router 
bit on top of the horizontal 
work piece while the router is 
in cutting position on top of 
the template.  Then you can 
simply move the depth 
indicator to the 12mm or 
15mm mark, plunge the router 
and you are ready to cut.   
 
Be careful here.  

Note that this 

is NOT 12mm from the base of 
the router, it is 12mm lower 
than the bit when it is 
positioned on top of the 
horizontal work piece with the 
router sitting in cutting 
position on top of the 
template. 

 

If you use some other brand of 
router be sure you can set the 
depth of cut from a bit zeroed 
on top of the work piece.  Do 
not try to set the bit depth of 
cut with the router on the 
bench as it will not be correct 
and your joints will be way off. 
 
Once the router bit depth is 
set, make the cuts.   Remove 
the pieces and try the fit.  
Usually the depth setting will 
produce a properly tight fit, 
but if it is off a bit lower the bit 
to make it tighter and raise the 
bit to loosen the joint fit.   
 

 

Check how flush the joint is 
when driven all the way home.  
If the vertical piece (what will 
normally be the side of your 
drawer) stands proud of the 
edge of the horizontal piece 
(which normally will be the 
front or back of your drawer), 
then loosen the two holding 
screws and turn each in/out 

adjusting wheel to the same 
mark in the + direction.  Note 
that the well engineered VS-
600 is calibrated so each mark 
represents an 0.1mm 
movement.  If your edge 
stands proud by 0.2mm, move 
the wheels two marks and 
tighten them down.  If the 
sides go in too far, move both 
wheels in the – direction by 
the proper amount. 
 
It is a good idea to do one 
more test cut if you needed to 
adjust either the router bit 
depth setting or the template 
in/out setting.  You only need 
to do this once and that 
template will forever be set to 
produce your prefect drawer 
no matter what length, width 
or thickness of work pieces 
you use (so long as the 
thickness is within the range 
specified for each template 
and you continue to use the 
same router bit). 
 
When you have the fit you 
want, save the pieces to use as 
a router depth of cut gauge for 
all subsequent uses of this 
template.   
 
The “right” fit is a matter of 
personal taste.  I like the joint 
to go together with only a light 
tapping with my hand or a 
mallet.  That will provide a 
good bonding surface for the 
glue and still show a tight, 
artful joint.  If the joint is 

 

33

Summary of Contents for VS-600
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands