Festool VS-600 Instruction Manual Download Page 18 | Manualshive

Page: 18 / 47

background image

unit with the in/out adjusting
wheels at each end against the
front edge of the VS-600.

Loosen the rotary knobs on the
two sides stops. Drop the
template down and align the
side stops to the inside of the
“D” shaped hole cut in each
side of the template.

Tighten the two rotary knobs
to hold the side stops in place.
Turn the side stop fingers so
SZ-14 or SZ-20 is facing
INWARD, towards the center
of the VS-600. The jig is now
ready to use.

So, how do you know
which piece goes where
and how they are
oriented on the VS-600?

Start by ignoring the drawings
and piece numbering text on
page 21 of the Festool VS-600
manual. I will show you a
much simpler method that you
can far more easily remember.

Place the drawer components
in front of you, standing
upright just like they will be
on your finished drawer with
the front of the drawer facing
you. Take a moment to look at
grain patterns and any defects
to determine the inside and
outside faces for each
component and which edge
should be the top of your
drawer. When you like the
arrangement, mark the

INSIDE FACE

of each

component and mark the edge
that is to be the

TOP

. I do this

by drawing a triangle with the
point up on the inside of each
component. Mark which is the

FRONT

piece and which is the

BACK

piece of your perfect

drawer. I write “f” or a “b”
inside the triangle to indicate
that to myself.

All of the cuts will take place
with the INSIDE face of each
component facing out, away
from the VS-600, and with the

TOP edge against the side

stops on the VS-600. The
Front and Back will be cut

horizontally clamped under

the top clamp bar. The sides

will be cut vertically clamped
under the front clamp bar.

You can’t go wrong if you
always have the inside face
away from the jig with the top
edge aligned with a side stop.
The front and back of your
drawer will always be cut
horizontally clamped by the
top clamp bar. The sides will
always be cut vertically
clamped by the bar on the
front of the VS-600. The order
in which you make your cuts

18

«
...
16
17
18
19
20
...
»

Summary of Contents for VS-600
















































Reviews:

No comments

Related manuals for VS-600

VisionXS-IP-F-DP-UHR

Brand: G&D Pages: 148

Brand: Vanderbilt Pages: 18

Brand: yellow jacket Pages: 2

Brand: Porter-Cable Pages: 19

BANDSAW BLADE SHARPENER

Brand: Woodland Mills Pages: 56

Brand: Ubermann Pages: 40

Brand: Xantrex Pages: 30

Brand: YATO Pages: 88

Brand: U-Line Pages: 12

Brand: Goobay Pages: 4

Brand: BRICK Pages: 30

Brand: Extech Instruments Pages: 19

Brand: MMP Pages: 10

Brand: Baileigh Industrial Pages: 40

Brand: King Canada Pages: 9

Brand: Hilti Pages: 84

Brand: Yost Vise Pages: 6

CERTI- LOK Hand Tool Frame Assembly 169400

Brand: TE Connectivity Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands