manualshive.com logo in svg

Festo EXCH-40-...-AB1 Series, Mechanical Installation

Share
Download
Festo EXCH-40-...-AB1 Series Mechanical Installation Download Page 7

1

Safety and requirements for product use

Festo – GDCP-EXCH-KM-KOMP-EN – 1506a – English

7

1

Safety and requirements for product use

1.1

Safety

1.1.1

General safety information

 Observe the safety instructions in the corresponding chapters.

Special safety regulations are immediately before the task instruction.

1.1.2

Intended use

The planar surface gantry EXCH-40/-60 (product) is designed for executing positioning tasks within

machines or automated systems with a higher-order controller.

 Use the planar surface gantry only as follows:

–

in perfect technical condition

–

in original condition, without unauthorised modifications

–

within the limits of the product defined in the technical data (

è

 A  Technical appendix)

Note

In the event of damage caused by unauthorised manipulation or other than intended

use, the guarantee is invalidated and the manufacturer is not liable for damages.

Summary of Contents for EXCH-40-...-AB1 Series









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands