manualshive.com logo in svg

Festo EXCH-40-...-AB1 Series, Mechanical Installation

Share
Download
Festo EXCH-40-...-AB1 Series Mechanical Installation Download Page 61

5

Mounting (horizontal mounting position)

Festo – GDCP-EXCH-KM-KOMP-EN – 1506a – English

61

5.3.3

Setting toothed belt pretensioning

Note

The pretension of the toothed belt diminishes during storage and operation. This is

normal and must not be changed by increasing the tension of the toothed belt. This

reduced pretension must not be used for evaluating the wear condition of the toothed

belt.

Belt tensioning device

1

1

End cap with belt tensioning device

Fig. 5.15 Depicted: EXCH-40-…-B (motor attachment position underneath)

1. Dismount cover of the belt tensioning device.

EXCH-40

EXCH-60

No dismounting (cover not present).

 Unscrew the 4 screws of the cover. Remove

cover.

1

2

3

1

End cap with belt tensioning device

2

Cover (belt tensioning device)

3

Screw (4x)

Fig. 5.16

Summary of Contents for EXCH-40-...-AB1 Series









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands