5
SUNN MODEL T50C – REAR PANEL*
off
high
low
output power
power
on
FUSE
footswitch
main
amp out
ext.
amp in
F
G
B
C
D
E
A
16
Ω
8
Ω
4
Ω
load impedance
MAX. PWR. OUT 70W RMS
ext.
spkr.
main
spkr.
MIN. LOAD 4
Ω
TOTAL
I
J
K
H
•
•
•
•
*NOTE: Rear Panel instructions and illustrations
are divided over pages (5 - 7).
A. POWER
- Push UP to switch the T50C ON. Push
DOWN to switch the T50C OFF.
B. FUSE
- Protects the T50C from electrical faults.
Replace
FUSES
only with same type and rating
(Refer to SPECIFICATIONS, F1, page 7). If the
T50C repeatedly blows
FUSES
, take the T50C to
an authorized Fender Service Center.
C.IEC LINE CORD CONNECTOR
- Connect the
LINE CORD
to a grounded AC receptacle in
accordance with the voltage and frequency rat-
ings shown on the Rear Panel of the T50C (See
illustration above,
INPUT POWER
{
D
}).
E. HIGH/LOW OUTPUT POWER
- Switch UP for 50-
Watts. Switch DOWN for 12.5-Watts (The
LOW
OUTPUT
setting was designed to provide the
same tone characteristics of the
HIGH OUTPUT
setting, at lower volume levels).
F. MAIN AMPLIFIER OUT
- When using the T50C as
the “
master
” amp in a “chain,” use this jack as
output to a “clone” amp, (See MULTIPLE T50C
CONNECTIONS, page 7).
G.EXTERNAL AMPLIFIER IN
- When using a T50C
as a “
clone
” amp in a “chain,” use this jack as
input from the “master” amp.
H.FOOTSWITCH
(INCLUDED) - Plug in the
FOOTSWITCH
at this jack. Use the
FOOTSWITCH
to:
•
•
•
•
Switch ON/OFF the
effects LOOP*
•
•
•
•
Switch ON/OFF the
REVERB effect
•
•
•
•
Select either
channel-1
or
channel-2*
*
NOTE: These switching functions are disabled
from the T50C’s cabinet switches when the
FOOTSWITCH
is plugged in.
I. EXTERNAL SPEAKER
- Plug in a maximum of
three
Sunn 112 Extension Cabinets
connected
together at this jack.
J. MAIN SPEAKER
- Connect the T50C’s
INTERNAL
SPEAKER
(or other speaker, 4
Ω
minimum) at this
jack. NOTE: The
MAIN SPEAKER
jack must
ALWAYS have a speaker connected to it when the
T50C is ON, or damage may occur to the T50C.
ALWAYS switch the T50C OFF before connecting
speakers.
K.LOAD IMPEDANCE
- Select an
IMPEDANCE
,
(4
Ω
/8
Ω
/16
Ω
)
that matches the total
SPEAKER-
LOAD IMPEDANCE
(both speaker jacks {
I
+
J
}
together): Standard parallel speaker connections
with their proper
LOAD IMPEDANCE settings
are
shown below:
{J} MAIN SPKR +
{I} EXT SPKR =
{K} LOAD
JACK
JACK
IMPEDANCE
SETTING
T50C Internal
(Speaker 16
Ω
)
+
NONE
=
16
Ω
T50C Internal
1 Sunn 112
(Speaker 16
Ω
)
+
(16
Ω
)
=
8
Ω
T50C Internal
2 Sunn 112’s
(Speaker 16
Ω
)
+
(8
Ω
)
=
4
Ω
T50C Internal
3 Sunn 112’s
(Speaker 16
Ω
)
+
(5.3
Ω
)
=
4
Ω
T50C Internal
Sunn 412
(Speaker 16
Ω
)
+
(16
Ω
)
=
8
Ω
T50C Internal
Any External
(Speaker 16
Ω
)
+
(8
Ω
)
=
4
Ω
Any External
(Speaker 8
Ω
)
+
NONE
=
8
Ω
Any External
Any External
(Speaker 8
Ω
)
+
(8
Ω
)
=
4
Ω
Any External
(Speaker 4
Ω
)
+
NONE
=
4
Ω
ENGLISH
ESP
AÑOL
DEUTSCH
FRAN
ç
AIS
IT
ALIANO
ENGLISHENGLISH
ESP
AÑOL
DEUTSCH
FRAN
ç
AIS
IT
ALIANO
Summary of Contents for Sunn T50C
Page 1: ......
