9
Specifications
Front Panel
LEVEL
BASS
TREBLE
STEREO
AUX IN
PHONES
STEREO
A.
LEVEL —
Adjusts the volume output from the Fender
Passport Studio speakers -OR- the volume output from the
STEREO PHONES jack {E}, when in use.
B.
POWER ON/CLIPPING LED —
This LED illuminates green
when the unit is powered on. This LED flashes red when the
power amp is clipping indicating that LEVEL {A} should be
reduced to prevent the unit from distorted sound output.
C.
BASS/TREBLE —
Use these switches to boost or attenuate
response in the low and high frequency ranges respectively.
The middle "0" position provides true flat signal response.
+1.5dB
75Hz
7.5kHz
BASS
TREBLE
–1.5dB
D.
STEREO AUX IN —
Connect this jack to the sound card
output on your computer or the headphones output on
an audio player with the supplied stereo mini cable. This
included cable can limit interference to other devices and
can be replaced by ordering Fender p/n 0097079000. You
may need to adjust the output level of the source device
to avoid clipping. NOTE: The STEREO AUX IN jack and the
BALANCED INPUTS {H} can be used simultaneously.
E.
STEREO PHONES —
You can plug in headphones to
this jack. The Fender Passport Studio speakers are
automatically muted.
Rear Panel
F.
POWER SWITCH —
Press to the "ON" position to turn the
unit on. Press to the "OFF" position to turn the unit off.
G.
VOLTAGE SELECTOR —
Change this setting only if you travel
to a country that requires a different voltage setting.
H.
BALANCED INPUTS —
These jacks can be used to input
balanced signals using 1/4" TRS (Tip-Ring-Sleeve) plugs where
Tip=Positive, Ring=Negative and Sleeve=Ground.
I.
POWER INPUT —
Connect to a grounded AC outlet in
accordance with the proper VOLTAGE SELECTOR {G} setting.
J.
FUSE —
Protects the unit in case of electrical faults. Replace
only with the type and rating specified above the fuse holder
on your unit.
K.
TO
RIGHT SPEAKER —
Connect this jack to the
input jack inside the rear compartment of the right speaker
using ONLY the included TRS (Tip-Ring-Sleeve) cable where
Tip=Woofer, Ring=Tweeter and Sleeve=Common. Do NOT
use a standard speaker cable for this connection! This cable
can be replaced by ordering Fender p/n 0097078000. See
POWER OUTPUT in
Specifications
below.
TYPE
PR 1193
FREQUENCY RESPONSE
SYSTEM:
50Hz–20kHz ±3dB
POWER AMP:
30Hz–20kHz ±1dB (resistive loads)
MAXIMUM SPL
105dB SPL Peak @ 1m
THD+NOISE
<0.2% @1W into resistive load (woofer output, 20Hz–5kHz)
<0.3% @250mW into resistive load (tweeter output, 3kHz–20kHz)
SYSTEM SIGNAL TO NOISE RATIO
>90dB, unweighted (22Hz–22kHz filter enabled)
NOMINAL INPUT LEVEL
–10dBV (3.5mm unbalanced stereo line inputs)
+4dBu (1/4” (6.35mm) balanced line inputs)
MAXIMUM INPUT LEVEL
+8.0dBV (3.5mm unbalanced stereo line inputs)
+22dBu (1/4” (6.35mm) balanced line inputs)
INPUT IMPEDANCE
10kΩ (3.5mm unbalanced stereo line inputs)
20kΩ (1/4” (6.35mm) balanced line inputs)
POWER OUTPUT
Woofers (LF): 100W (50W/channel) 200Hz into 4Ω @ <0.7% THD+N
Tweeters (HF): 50W (25W/channel) 8kHz into 8Ω @ <0.2% THD+N
POWER REQUIREMENT
100–120V or 220–240V 50/60Hz; 250W maximum
FUSE
F6.3AH 250V 5mm x 20mm
SYSTEM DIMENSIONS
WIDTH:
18 in (45.7 cm)
HEIGHT:
14 in (35.6 cm)
DEPTH:
8.25 in (21.0 cm)
WEIGHT
SYSTEM:
18.5 lb (8.4 kg)
SHIPPING:
24 lb (10.9 kg)
Product specifications are subject to change without notice.
EN
GL
ISH
