XL-1S Hookup and Installation Instructions
4–2
Mounting 6805 Keypad
Keypads can be surface mounted or flush mounted as described below. NOTE: After mounting the 6805 LCD
Keypad at eye level, you can adjust the display intensity level to suit the user by adjusting the intensity
control located behind the keypad door.
SURFACE MOUNTING
1. Select a mounting location and place the rear plate of the
keypad on the wall. Mark the location of the cutout for the
keypad wiring cable.
2- Create a keypad opening. Connect the keypad wiring to
the control panel w/ 4-wire connector.
3- Place the keypad wiring through the cutout and secure the
back plate to the wall (see diagram).
4- Connect the keypad wiring connector to the keypad and
place the keypad on the mounting plate attached to the wall.
5- Secure the keypad to the rear mounting plate by attaching
the 5/8-inch screw provided in the lower hole, located behind
the keypad door.
RECESSED MOUNTING
1- Select a mounting location. For recessed mounting this
must be between two studs. The rear mounting plate is not
used for recessed installations.
2- Create an opening in the wall exactly 4 inches high by 5
13/16 inches wide.
3- Turn over the keypad and remove the Phillips head screw
(item 1 on diagram) in the upper left hand side of the keypad
printed circuit board. NOTE: This screw is located
immediately to the left of the keypad connector.
4- Attach the black metal mounting strap to the rear of the
keypad as follows (see diagram);
- Face the pointed end of the mounting strap facing the
keypad front. This will be used to latch onto the inside of the
wall.
- Place the small white plastic spacer underneath the
mounting strap. Secure the mounting strap using the 5/8-
inch Phillips head screw (supplied) and the plastic spacer to
location 1.
- Secure the other end of the strap (location 2 on diagram) to
the white plastic opening using the Phillips head screw
removed in step 2.
5- Connect the white plastic tab into the round opening
immediately behind the keypad door. Place the longer
Phillips head screw (included) through the opening inside the
keypad door and begin to tighten the screw. Tighten the
screw and leave the tab in a down position.
6- Run the keypad wiring to the control panel and attach the
wiring to the keypad.
7- Place the keypad into the wall opening with the side
containing the black metal strap first until it grabs the inside
of the wall.
8- After inserting the side of the keypad with the metal strap,
insert the other side into the opening until the entire keypad
is firmly in the wall.
9- Tighten the screw inserted in step 5.
5
13
/
16
,,
4
,,
(15 cm)
(10 cm)
2
1
3
Summary of Contents for XL-1S
