Introduction
CPC307
C P C 3 0 7 U s e r M a n u a l
6
© 2 0 2 2 F a s t w e l v . 0 0 6
Figure 4.32: Diagram of the module's power supply voltage supervisor
………………………………………….…..77
Figure 4.33: Numbering pins of the XP14 connector
….………………………….………………… .………………..79
Figure 4.34: Connection of LEDs to the XP3
…………………………………………………………………..………..84
Figure 5.1: Screen during the module boot (POST)..
……………………………………… ………………………...86
Figure 5.2:
Screen of the “Main” menu ……………...…….……………………………………………………….......87
Figure 5.3:
Screen of the “Advanced” menu…………………...…………………………….....…….………………..88
Figure 5.4:
Screen of the “CPU Configuration” menu …………….…………………………………………….........89
Figure 5.5:
Screen of the “IDE Configuration” menu ………………………………….………………………….…..90
Figure 5.6:
Screen of the “Primary IDE Master” menu ...……..…………………………… ………………………...91
Figure 5.7:
Screen of the “Remote Access Configuration” menu………….…………………………………….......93
Figure 5.8:
Screen of the “USB Configuration” menu …...…...…………………………….....…….………………..95
Figure 5.9:
Screen of the “USB Mass Storage Device Configuration” menu………...……………………….........96
Figure 5.10:
Screen of the “PCIPnP” menu …………..………………………………….………………………….…..97
Figure 5.11:
Screen of the “Boot” menu ……………………………………………………… ………………………...99
Figure 5.12: Screen
of the “Boot Settings Configuration” menu ………………………………………………….....100
Figure 5.13:
Screen of the “Security” menu …………………...…………………………….....…….………………..102
Figure 5.14:
Screen of the “Chipset” menu ………………………….…………………………………………….......103
Figure 5.15:
Screen of the “South Bridge” menu …….………………………………….………………………….…104
Figure 5.16:
Screen of the “ISA Configuration” menu ………..…………………………….....…….………………..105
Figure 5.17:
Screen of the “Serial/Parallel Port Configuration” menu….……………………………………….......106
Figure 5.18:
Screen of the “WatchDog Configuration” menu…….…………………….………………………….…108
Figure 5.19:
Screen of the “GPIO and I2C Configuration” menu .......….……………………………………….......109
Figure 5.20:
Screen of the “CAN and COM5,6 Configuration” menu ……...………….………………………….…111
Figure 5.21:
Screen of the “Exit” menu……………………………….. ……...………….………………………….…112
All information in this document is provided for reference only, with no warranty of its suitability for any specific purpose. This information has been thoroughly checked and
is believed to be entirely reliable and consistent with the product that it describes. However, Fastwel accepts no responsibility for inaccuracies, omissions or their
consequences, as well as liability arising from the use or application of any product or example described in this document.
Fastwel Co. Ltd. reserves the right to change, modify, and improve this document or the products described in it, at Fastwel's discretion without further notice. Software
described in this document is provided on an “as is” basis without warranty. Fastwel assumes no liability for consequential or incidental damages originated by the use of
this software.
This document contains information, which is property of Fastwel Co. Ltd. It is not allowed to reproduce it or transmit by any means, to translate the document or to convert
it to any electronic form in full or in parts without antecedent written approval of Fastwel Co. Ltd. or one of its officially authorized agents.
Fastwel and Fastwel logo are trademarks owned by Fastwel Co. Ltd., Moscow, Russian Federation. Ethernet is a registered trademark of Xerox Corporation. IEEE is a
registered trademark of the Institute of Electrical and Electronics Engineers Inc. Intel is a trademark of Intel Corporation. Microsoft is a trademark of the Microsoft
corporation. In addition, this document may include names, company logos and trademarks, which are registered trademarks and, therefore, are property of their
respective owners. Fastwel welcomes suggestions, remarks and proposals regarding the form and the content of this Manual.
Ownership rights
This document contains information that is the property of Fastwel Group. It may not be copied or
transmitted by any known means, nor may it be stored in information storage and retrieval systems
without the prior written consent of Fastwel Group or one of its authorized agents. The information
contained in this document, to the best of our knowledge, is free from any errors, however, Fastwel
Group accepts no responsibility for any inaccuracies and their consequences, as well as liability
arising from the use or application of any diagram, product or example given in this document.
Fastwel Group reserves the right to change and improve both this document and the product
presented inside of it at its discretion without any further notice.
Safety requirements
This Fastwel Group’s product is developed and tested for the purpose of ensuring compliance to
the electric safety requirements. Its design provides long-term trouble-free operation. The service
life of the product can be significantly reduced due to the improper handling during unpacking and
installation. Therefore, in the interests of your safety and in order to ensure proper operation of the
product, you should follow the recommendations below.
