Farm King 12112 Operator And Parts Manual Download

Page: 110 / 158

Maintenance - Backsaver Auger 12112 / 12122

110

AXLE

Wheel Bolt Torque

Check the torque on wheel bolts daily. Tighten bolts to
110 - 125 lb. / ft. (149 - 169 N•m) torque.

Tire / Wheel Replacement

Empty the Backsaver Auger (if required).

Park the tractor / equipment on a flat level surface.

Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position.

Place chock blocks behind and in front of the auger
tire(s).

Place a jack under the axle frame on the side the wheel is
to be replaced. Raise the jack until the wheel is slightly
off the ground.

NOTE: Place blocks under the frame to help secure

the auger when wheel is raised off the ground.

Figure 183

Tighten wheel bolts in a criss-cross pattern

[Figure 183]

Tighten wheel bolts to 110 - 125 lb ft (149 - 169 N•m) of
torque.

Lower the axle and tires to the ground. Remove the lifting
device.

Check tire pressure.

NOTE: Recommended tire pressure is 45 - 50 PSI

(310 - 345 kpa). Maximum tire pressure of 60
PSI (415 kpa).

AVOID INJURY OR DEATH

Before you leave the operator’s position:

•

Always park on a flat level surface.

•

Place all controls in NEUTRAL.

•

Engage the park brake.

•

Stop the engine and remove the key.

•

Wait for all moving parts to stop.

AVOID INJURY OR DEATH

•

The parking brake must be engaged before
leaving the operator’s position. Rollaway can
occur because the transmission may not
prevent machine movement.

•

Always chock tires before performing any
maintenance or service.

B-1018

Summary of Contents for 12112































































































































































Search results

Summary of Contents for 12112

Reviews:

Related manuals for 12112

Brands by name

Popular brands

Farm King 12112, Operator And Parts Manual

Search results

Summary of Contents for 12112

Reviews:

Related manuals for 12112

Brands by name

Popular brands