RESTRICTED USE ONLY
Fargo Electronics, Inc.
Persona
C11 Card Printer and Persona
M11 Card Printer User Guide (Rev. 5.0)
214
DC (Direct Current), 196
DC Motor, 196
Default, 196
Default button, 97, 104, 160
Default Heat button, 154
default ISO Standard selections, 107, 110, 163, 165
default location, 140
defined area, 123, 177
Defined Area arrows, 124, 178
Defined area(s), 139
Defined Area(s) check box, 139, 140, 141, 145, 146, 147
Defined Area(s) option, 118, 120, 137, 173, 174
Defined/undefined area(s), 136, 138
Defrag, 196
Delete button, 124, 178
developer solution, 52
Device Manager tab, 32
Device Option tab, 43
Digital Voltmeter, 36, 42
dimension boxes, 140
Dimensions, 15
DIP Switch, 68
DIP Switch Settings table, 68
DIP switches (Dual In-line Package Switches), 196
Direct-to-Card (DTC) Printing, 197
Disable Printing option, 93, 152
Disables Magnetic Verification, 69
disk cleanup utility, 32
Dither, 197
dither method, 90, 149
DMA (Direct Memory Access), 195
Dongle, 197
Dot, 197
Dot pitch, 197
Download, 197
DPI (Dot Per Inch), 197
DRAM (Dynamic Random Access Memory), 197
Driver, 197
Duplex Printing, 197
Dwell Time, 198
Dye Migration, 198
Dye-Sub Intensity setting, 58
Dye-Sublimation, 19, 198
Dye-Sublimation Black (BO), 24
Dye-Sublimation Black Panel, 21
Dye-Sublimation Cyan Panel, 21
Dye-Sublimation Magenta Panel, 21
Dye-Sublimation Yellow Panel, 21
Dye-Sublimation-Only Print Ribbon, 24
Dye-Sublimation-Only Print Ribbons, 23
E
E-card, 198
E-card Docking Station, 198
ECP Mode (Enhanced Capabilities Port Mode), 198
Edge-to-Edge, 198
EE Memory, 198
EEPROM (Electrically Erasable Programmable Read
Only Memory), 198
embedded contaminants, 25, 55
Emissions Standards, 14
Enable MLE Support checkbox, 108
Encoder (smart card), 198
Encoder (wheel), 199
Encoder Sensor, 42
End Sentinel (ES)., 114, 169
Engine, 199
Enhanced Communication Port (ECP) mode, 32
EOF (End Of Form), 199
EPP (Enhanced Parallel Port), 199
EPROM (Electronically Programmable Read Only
Memory), 199
EPROM version number, 67
Escape sequence, 199
ESD, iv, 77, 179, 187
ESD (ElectroStatic Discharge), 199
Ethernet, 199
excessive resin printing problems, 60, 61
Extended Capabilities Port, 21
external device interference, 31, 32
F
Fargo Technical Support, 190
Fargo Technical Support via the Web, 190
FCC, 13
feed card into encoder, 31, 52, 53
Field Separator (FS), 114, 169
Film, 199
Firmware, 199
Flash Memory, 200
Font, 200
For Overlay Only, 119
For Print and Overlay, 119
formatting magnetic string, 53
FPGA (Field Programmable Gate Array), 200
FRONTSIDE plate, 64
Full bleed, 200
Full Card option, 118, 136, 173
G
Gamma, 200
Glossy PVC, 200
Glossy/Matte, 200
Graphical Device Interface (GDI), 200
Gray Scale, 200
H
Halftoning, 200
Hard Drive, 201
hard drive space
adequate or inadequate, 32
HDP (High Definition Printing
™
), 201
Head, 201
Head Up/Down Error, 35
Headlift Motors, 35
Headlift Sensors, 35
Heat (M11 only) option, 154
Heat Seal, 201
Heat sink, 201
HiCo (High Coercivity), 201
