Fargo DTC4500 User Manual Download Page 32

Page: 32 / 140

2011

HID

Global

Corporation

All

rights

reserved

DTC4500

Card Printer/Encoder User Guide L001444 Rev1.1

Swift ID Installation Instructions

Here are the related definitions for the Swift ID installation instructions.

•

Swift ID:

This is a ‘built-in badging’ application which enables Users to create simple ID badges

without having to install any additional software. (

Note:

This application is only intended for use

between one Printer and one PC. The application cannot select between Printers; also, only one
Printer on a PC can access Swift ID.)

•

HID EEM Driver:

This Driver is used by Swift ID to communicate with the PC when connected via a

USB cable. (

Note:

It is also known as an ‘ETHERNET Emulation Module’.)

•

EEM Device Flag (i.e., Enable Swift ID over a USB connection):

Check this item to utilize Swift ID

via a USB connection. (

Note:

When this box is checked, the Ethernet connection (if applicable) on the

Printer will not be operational.)

If this flag or selection is not accessible, it means the HID EEM Driver (that Swift ID uses to

connect via a USB connection) has not been installed. (

Note:

This Driver can be found on the

installation CD or it can be downloaded from the HID Global support page.)

Summary of Contents for DTC4500






























































































































Search results

Summary of Contents for DTC4500

Reviews:

Brands by name

Popular brands

Fargo DTC4500, User Manual

Search results

Summary of Contents for DTC4500

Reviews:

Brands by name

Popular brands