Fargo DTC4500 User Manual Download Page 108

Page: 108 / 140

2011

HID

Global

Corporation

All

rights

reserved

DTC4500

Card Printer/Encoder User Guide L001444 Rev1.1

108

Troubleshooting with the Error Message Table

Error Message

Cause

Solution

# 144

EEPROM Corrupt

EEPROM Read
Error

EEPROM restored with factory
default values.

•

If changes were made in the

Advanced Setting Tab in the
Printer Driver, click the

Default

button to reset these

numbers.

•

Reset the Printer and try

again. If this problem
persists, call for technical
assistance.

# 170

Ribbon Calibration
failed

Ribbon calibration failed.

Check for material blocking
sensor and try again.

#202

Encoder not
installed

You are trying to send
encoding data, but the Printer
is not configured with this
Encoder type.

iCLASS,Prox,Mifare,SmartCard

•

Ensure that no encoding

data is being sent with the
print job and reprint the card.

•

Install an Encoding Module.

No UV Protection

Ribbon type selected does not
contain an overlay or
overlaminate

The current printer driver setup
does not have any protective
coating being applied to the
front or back of the card. Select
YES to continue or NO to alter
the settings.

Summary of Contents for DTC4500






























































































































Search results

Summary of Contents for DTC4500

Reviews:

Brands by name

Popular brands

Fargo DTC4500, User Manual

Search results

Summary of Contents for DTC4500

Reviews:

Brands by name

Popular brands