Fargo DTC4500 User Manual Download Page 101

Page: 101 / 140

2011

HID

Global

Corporation

All

rights

reserved

DTC4500

Card Printer/Encoder User Guide L001444 Rev1.1

101

Troubleshooting with the Error Message Table

Error Message

Cause

Solution

# 45

No Flip Module
installed

Request to print on 2

side of

card, but no Flipper is installed.

If a Flipper Module is present,
ensure that the Print Both Sides
option in the Printer Driver is set
correctly.

Install a Flipper module.

# 48

Check Lam Power

Lam is connected but not
powered.

Power off the Printer, power the
Laminator, and then power on
the Printer.

A damaged Flipper board, E-
Card board, or EEPROM could
potentially result in this same
error.

# 52

Lam Generic Error

Laminator firmware error

Cycle power and try again.

If this problem persists call for
technical assistance.

# 53

Lam Card Jam

A jam occurred somewhere
between the Printer and the
Laminator

Open covers and clear the
obstruction/jam

# 63

Lam Tag Error

There is no material loaded in
the Laminator

Load material into the
Laminator

Summary of Contents for DTC4500






























































































































Search results

Summary of Contents for DTC4500

Reviews:

Brands by name

Popular brands

Fargo DTC4500, User Manual

Search results

Summary of Contents for DTC4500

Reviews:

Brands by name

Popular brands