Fanotec MECHA C1 User Manual Download Page 37

Page: 37 / 122

MECHA User’s Guide

v.06

‒ Single Axis

●

[Shoot]

button — Shoots the number of photos in a set for a single

position. In our example, 1 photo is taken (

1 TRG

). Use this feature when

you want to take some photos in a certain position, without any rotation.

●

[N x RIGHT]

button — The same as

[N x LEFT]

, but the shooting and

rotation are done clockwise.

●

[Cancel]

button — Executes a smooth stop.

●

[PAUSE] button

— Pauses the current running preset. Click/tap again this

button to continue.

○

The

21<

code switches MECHA to or off pause mode, the same as

clicking the

[Pause]

button on UI, or on IR Remote.

○

When MECHA is in pause mode, the LEDs blink like

(a colon). In idle

status, there is a slow blink, and when running presets and paused,

there is the regular blink.

○

When MECHA runs a preset and is paused, you can press

, or

on IR Remote, or

[PAUSE/NEXT]

on UI, to continue to the next position.

○

If, instead,

is pressed on C2 or on IR Remote, MECHA will continue

to the next position and switches on/off the step by step mode.

The above allows both:

1. Starting a preset in step by step, then switch off step by step when it is

not needed, thus the preset will continue automatically.

2. If a preset is paused by remote/UI/script, then pressing

will advance

and switch on/off the step by step.
A possible application is a spherical panorama with certain areas

needing to be done step by step, and which areas depends on the events

on the field.

During the pause, pressing

on IR Remote, or

[SHOOT]

on UI, MECHA

will trigger the number of shots specified by

[TRG]

in presets.

This can be used for extra shots for a particular position.

●

[STOP]

— Emergency stop.

Summary of Contents for MECHA C1



























































































































Search results

Summary of Contents for MECHA C1

Reviews:

Brands by name

Popular brands

Fanotec MECHA C1, User Manual

Search results

Summary of Contents for MECHA C1

Reviews:

Brands by name

Popular brands