manualshive.com logo in svg

Fanotec MECHA C1, User Manual

Share
Download
Fanotec MECHA C1 User Manual Download Page 105

105

MECHA User’s Guide

v.06

© 2021 FANOTEC

Current Codes list

1<

or

1>

Executes the

Preset 1

to the left or to the right.

By default, the

Preset 1

consists of 4 shots around, or it is the preset

saved with the

[Save1]

UI button.

2<

or

2>

Executes the

Preset 2

to the left or to the right.

By default, the

Preset 2

consists of 6 shots around, or it is the preset

saved with the

[Save2]

UI button.

3<

or

3>

Executes the

Preset 3

to the left or to the right.

By default, the

Preset 3

consists of 8 shots around, or it is the preset

saved with the

[Save3]

UI button.

131<

or

131>

Executes a panorama of 6 shots around to the left or to the right, for a

single MECHA.

132<

or

132>

Executes a panorama of 12 shots around to the left or to the right, for a

single MECHA.

1312<

or

1312>

Executes a panorama of 12 shots around, 3 rows ‒ at 0° and at +/-45° ‒

plus zenith and nadir, to the left or to the right, for MECHA DAC. The code

must be entered on MECHA-H, and MECHA-V must be

parked

, i.e.

oriented upward, as for the zenith photo.

1313<

or

1313>

The same as 1312, but with MECHA-V in the

level

position. First time,

please test the codes without camera mounted on the panohead.

1321<

or

1321>

The same as 1312, but with MECHA-V in the

raised

position. First time,

please test the codes without camera mounted on the panohead.

Summary of Contents for MECHA C1



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands