background image

OPERATION 

 

WERKING 

 

 

 

General 

 

Algemeen 

 

 

 

It is the responsibility of the Owner to ensure that the 
operation of an agricultural tractor and any attached 
equipment is carried out in accordance with all applicable 
laws, regulations and practices relating to safe and 
responsible operation. 

 

Dit is die verantwoordelikheid van die eienaar om te verseker 
dat die bedryf van ‘n landboutrekker en enige gekoppelde 
toerusting uitgevoer word in ooreenstemming met alle 
toepaslike wette, regulasies en praktyke wat met veilige en 
verantwoordelike bediening te doen het. 
 

-

 

Applicable regulations should include but not be limited 
to the South African Occupational Health and Safety 
Act No. 83 of 1993 and the South African National Road 
Traffic Act No. 93 of 1996. 

-

 

Refer also to operational information relevant to the 
tractor concerned, including handbooks, operators 
manuals, safety and warning notices and decals. 

 

-

 

Toepaslike regulasies sluit in, maar is nie beperk tot, die 
Suid-Afrikaanse Wet op Beroepsgesondheid en Veiligheid 
nr. 85 van 1993 en die Suid-Afrikaanse Wet op Nasionale 
Padverkeer nr. 93 van 1996 nie.

 

-

 

Verwys ook na tersaaklike bedryfsinligting oor die 
betrokke trekker, insluitend handboeke, operateurs-
handleidings, veiligheid en waarskuwingskennisgewings 
en -plakkers. 

 

 

 

Preparation for use 

 

Voorbereiding vir gebruik 

 

 

 

W

 

Only suitably trained persons should operate the 
implement and no person should operate the 
implement without first studying and establishing a 
complete understanding of the content of this manual. 

 

W

 

Slegs toepaslik opgeleide persone moet die implement 
bedryf, en geen persoon moet dit bedryf sonder om eers 
die inhoud van hierdie handleiding te bestudeer en ’n 
volledige begrip daarvan te verkry nie. 

 

 

 

The implement should be thoroughly inspected and 
prepared before each use and with reference to procedures 
described elsewhere in this manual. 

 

Die implement moet telkens eers deeglik geïnspekteer en 
voorberei word voor dit gebruik word en met verwysing na 
prosedures wat in ander dele van hierdie handleiding beskryf 
word. 

1.

 

Attaching the implement to the tractor. 

2.

 

Installing the PTO driveshaft. 

3.

 

Settings and adjustment. 

4.

 

Lubrication and oil levels. 

5.

 

Routine maintenance (before and after each use).

 

 

1.

 

Koppeling van die implement aan die trekker. 

2.

 

Installering van die kragaftakkeras. 

3.

 

Instellings en verstellings.  

4.

 

Smering en olievlakke.

 

5.

 

Roetine-instandhouding (voor en na elke gebruik).

 

 

 

 

Inspect the work area. 

 

Inspekteer die werksgebied. 

/

 

Remove any movable obstructions from the work area, 
especially any object which may become a projectile.

 

/

 

Note the presence of holes, stumps, rocks, or any other 
obstruction that might destabilise the tractor or cause 
damage to the implement. Remove these obstacles 
where possible, otherwise note and avoid these areas 
during cutting. 

 

/

 

Verwyder enige los obstruksies van die werksgebied, 
veral enige voorwerp wat dalk ‘n projektiel mag word. 

/

 

Let op enige dongas, gate, stompe, klippe, of enige ander 
obstruksie wat die trekker mag destabiliseer of die 
implement kan beskadig. Verwyder hierdie hindernisse 
waar moontlik, of anders moet hierdie gebiede 
gedurende sny vermy word.

 

 

 

 

Operating the implement 

 

Bedryf van die implement 

 

 

 

W

 

Never approach, or allow anyone else to approach, the 
implement unless the implement has been lowered to 
the ground, the tractor engine shut off and the 
handbrake applied, and the implement’s cutting gear 
has come to a complete stop. 

W

 

Actively discourage spectators and cease operation of 
the implement if any person approaches or enters the 
work area. 

W

 

Operate the implement only at the specified PTO shaft 
speed. 

 

W

 

Moet nooit die implement benader, of toelaat dat 
enigiemand anders dit doen, tensy die implement op die 
grond laat sak is, die trekkerenjin afgeskakel is, die 
handrem opgetrek en die implement se snymeganisme 
heeltemal tot stilstand gekom het nie.  

W

 

Toeskouers moet aktief ontmoedig word. Snywerk moet 
onmiddellik gestaak word as enige persoon die 
werksgebied benader of dit betree.  

W

 

Verseker dat die implement slegs teen die 
gespesifiseerde kragaftakkerasinsetspoed bedryf word. 

11

Summary of Contents for Rotagang F210 TurfPro







































Reviews: