SERVICING WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
26
8
To Remove a Hotplate Tap
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3.
c) Undo
compression
fi tting at the rear of the tap. Remove
the fi xings that secure the tap to the gas rail. Disconnect
the ignition switch wiring.
d) Remove the tap. Remove and discard the gasket seal. Fit
new gasket seal to replacement tap.
e) Re-assemble in reverse order. Check the appliance is gas
sound. Check hotplate ignition.
9
To Change an Ignition Switch
Change the gas tap as detailed in Section 9.
10 To Remove a Hotplate Burner Injector
a) Remove the hotplate as detailed in Section 2.
b) Remove the injector directly from the burner body.
c) Fit the appropriate injector.
d) Re-assemble in reverse order. Check the appliance is gas
sound.
11 To Remove a Hotplate Burner Spark Electrode
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Undo the bezel venturi and remove the bezel from the
hotplate. The spark ignition wire will be pulled through
the electrode clearance hole.
c) Disconnect the spark electrode from the ignition wire.
Note
Take care to prevent the ignition wire from falling back through
the clearance hole.
d) Undo the spark electrode from the bezel by removing the
spring clip and spring.
e) Fit the replacement electrode to the burner bezel. Ensure
that the spring and clip are properly located.
f ) Replace in reverse order and check correct burner
ignition.
12 To Remove a Hotplate Burner
a) Remove the pan supports, hotplate accessories and
burner heads.
b) Remove the hotplate as detailed in Section 2.
c) Remove the nut that secures the burner body to the
support channel.
d) Remove the fi xings that secure the support channel to
the chassis. Lift the channel clear of the appliance.
e) Undo the compression fi tting which connects the burner
body to the gas pipe. Remove the burner body from the
appliance.
f ) Replace in reverse order. Check the appliance is gas
sound and that the burner operates satisfactorily.
13 To Remove an Oven Door
a) Open the oven door.
b) Support the door and remove the two screws which
secure the upper hinge to the front frame of the unit.
c) Remove the door from the lower hinge by lifting slightly
and moving it outward.
d) Re-assemble in reverse order.
14 To Remove the Oven Outer Door Panel
a) Open the oven door.
b) Remove two screws ‘A’ and two screws ‘B’ from the door.
c) Remove the outer door panel.
d) Undo the nuts that secure the handle to the door panel.
Fit the handle to the replacement door panel.
e) Fit the replacement panel to the oven inner door.
f ) Re-assemble in reverse order.
15 To Remove the Door Latch
a) Remove the oven outer door panel as detailed in Section
15.
b) Remove the fi xings that secure the latch assembly to the
inner door panel.
c) Fit the replacement catch and re-assemble in reverse
order.
d) Check correct operation of door.
16 To Remove the Oven Door Seal
a) Open oven door. The seal is held in place by small hooks
on the rear face. At the corner pull seal diagonally away
from the door centre until that hook is released.
b) Proceed to the next hook and release it in a similar way,
and so on. Use force if the hooks are stiff , as the old seal
will be discarded.
c) When
fi tting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of
the door, and proceed round the door snapping in each
hook in turn.
