SERVICING WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
25
Servicing
1 SERVICING
When servicing or replacing gas carrying components,
disconnect from the gas supply before commencing operation.
Check the appliance is gas sound after completion of service.
When checking for gas leaks do not use washing up liquid - this
can corrode. Use a product specifi cally manufactured for leak
detection.
Do not use re-conditioned or unauthorised gas controls.
Disconnect from the electricity supply before commencing
servicing, particularly before removing any of the following:
- control panel, side panels, hotplate tray or any electrical
components or covers.
Before electrical re-connection, check that the appliance is
electrically safe.
Note - References to LH and RH oven apply as viewed from the
front.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS. TURN
OFF THE GAS SUPPLY.
2
To Remove the Hotplate
Disconnect the appliance from the electricity supply.
Pull the unit forward to gain access.
a) Remove the pan supports/hotplate accessories and
burner caps.
b) Remove the brass venturi in the centre of each hotplate
burner bezel.
c) Remove the bezel from the hotplate and disconnect the
spark ignition lead from the spark electrode.
d) Lift the hotplate clear of the appliance.
e) Replace in reverse order.
3
To Remove the Control Panel
Disconnect the appliance from the electricity supply.
a) Remove the pan supports/hotplate accessories and
burner caps.
b) Slacken the brass venturi at the centre of each burner.
c) Remove the control knobs from all taps.
d) Open both oven doors. Remove 3 fi xings on the top front
and 3 fi xings on the control panel underside.
e) Pull the control panel forward. Remove the connections
from the rear of the three neons. Disconnect the earth
lead and lift the panel clear of the unit.
f ) Replace all parts in reverse order.
g) When replacing any electrical connections refer to the
wiring diagram.
4
To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the retaining screw on the upper front edge
and the two fi xings on the rear or the side panel. Undo
the lower retaining screw situated below the edge at the
panel front corner.
c) Remove the panel by pulling it away from the unit.
Should diffi
culty be encountered, it may be necessary to
slacken the two closest burners and both brass venturi as
detailed in Section 2.
d) Replace parts in reverse order. Ensure that both venturis
are fully tightened.
5
To Remove an Oven Neon
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the relevant neon connection and undo the nut
which secures the neon to the control panel.
c) Replace parts in reverse order. Ensure the replacement
neon functions correctly.
6
To Remove a Thermostat
Disconnect the appliance from the electricity supply.
Remove the hotplate - see 2. Remove the control panel - see 3.
Open the appropriate oven door and remove the oven shelves.
Pull the appliance forward to gain access to the rear cover box.
Undo the cover screws and lift clear.
Right Hand oven
Remove the two fi xings that secure the thermostat phial cover.
Unclip the thermostat phial from the clips in the oven back
panel.
Left Hand oven
Remove the two screws holding the thermostat phial to the
oven fan cover at the rear of the oven. Pull the unit forward
to access the rear of the cooker. Remove the cover boxes
by removing the fi xing screws and lifting clear. Feed the
thermostat capillary clear of the oven.
Disconnect the wires from the thermostat and undo the two
fi xings that secure the control to the mounting plate.
Fit the replacement and re-assemble in reverse order. Ensure
that the phial is clipped to the oven rear, positioned centrally
between the clips. Check that the thermostat functions
correctly.
7
To Remove an Oven Cut-Off Thermostat
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to gain access to the cover box.
Undo the cover screws and lift clear.
b) The control is located on the earth plate beside the oven
element connections.
c) Disconnect the thermostat wiring. Undo the fi xings that
secure the thermostat to the earth plate and remove.
d) Fit replacement control and re-assemble parts in reverse
order.
