background image

 8  WARRANTY

The manufacturer guarantees correct device functioning. It also undertakes  to repair or replace the

device  if its defects  result from  material  or structural  faults. The warranty period is 24 months  from the
purchase date, fulfilling the following conditions:

Installation has been performed by an authorised individual, as per manufacturer recommendations.

Seals remain intact and no unauthorised structural changes have been made. 

The device has been used in accordance with its intended use as per user manual. 

Damage is not a result of improperly made electrical system or atmospheric phenomena. 

The manufacturer is not liable for damage which occurred as a result of improper use or mechanical
damage. 

In case of failure, the device must be submitted for repair with a Warranty Card. Defects  revealed within the
warranty period will be removed free of charge no longer than 14 days after accepting the product for repair.
Warranty and post-warranty repairs are performed by the manufacturer i.e. FAKRO PP. Sp. z o.o.

Quality certificate:

Device

Model............................................................................................................................................

Serial number...............................................................................................................................

Seller.............................................................................................................................................

 Address...........................................................................................................................................

Date of purchase.............................................................................................................................

...............................................................................................................

Signature (stamp) of installing person 

13.11.21 NC825-GB

14/16

©2013, 

FAKRO

Summary of Contents for ZWMA

















Reviews: