Fagor CNC 8070, Programming Manual

Page: 416 / 556

‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
Programming manual
402
CNC 8070
14.
CNC VARI
ABLES
Tool
r
e
la
te
d
(S
OFT
V02.0
X
)
382
The following variables may be accessed from the program (PRG), PLC and interface (INT) are
read-write (R/W).
If in the tool variables, the offset number is left out, the variable will then refer to the active offset.
(V.)TM.MZWAIT There is no need to program it in the subroutine associated with
M06
. The
subroutine itself waits for the manager's maneuvers to finish. This way, block preparation is not
interrupted.
GEOMETRY
Rot
Lin
Spd
(V.)[n].TM.TOR[i] Radius of the tool offset [i] of the active tool — —
(V.)TM.TORT[m][i] Radius of the tool offset [i] of the [m] tool — —
(V.)[n].TM.TOI[i] R wear of the [i] offset of the active tool — —
(V.)TM.TOIT[m][i] R wear of the [i] offset of the [m] tool — —
(V.)[n].TM.TOL[i] Length offset [i] of the active tool — —
(V.)TM.TOLT[m][i] Length of the tool offset [i] of the [m] tool — —
(V.)[n].TM.TOK[i] L wear of the [i] offset of the active tool — —
(V.)TM.TOKT[m][i] L wear of the [i] offset of the [m] tool — —
(V.)[n].TM.TOTIPR[i] Tool tip radius of the [i] offset of the active tool — —
(V.)TM.TOTIPRT[m][i] Tool tip radius of the [i] offset of the [m] tool — —
(V.)[n].TM.TOWTIPR[i] Tool tip radius wear of the [i] offset of the active tool — —
(V.)TM.TOWTIPRT[m][i] Tool tip radius wear of the [i] offset of the [m] tool — —
(V.)[n].TM.TOCUTL[i] Cutting length of the [i] offset of the active tool — —
(V.)TM.TOCUTLT[m][i] Cutting length of the [i] offset of the [m] tool — —
(V.)[n].TM.TOAN[i] Penetration angle of the [i] offset of the active tool — —
(V.)TM.TOANT[m][i] Penetration angle of the [i] offset of the [m] tool — —
(V.)[n].TM.TOFL[i].Xn Xn axis deviation of the [i] offset of the active tool Yes No
(V.)[n].TM.TOFL1 Offset of the tool in the first axis of the channel Yes No
(V.)[n].TM.TOFL2 Offset of the tool in the second axis of the channel Yes No
(V.)[n].TM.TOFL3 Offset of the tool in the third axis of the channel Yes No
(V.)TM.TOFLT[m][i].Xn Xn axis deviation of the [i] offset of the [m] tool Yes No
(V.)[n].TM.TOFLW[i].Xn Xn axis deviation of the [i] offset of the active tool Yes No
(V.)[n].TM.TOFLW1 Wear offset of the tool in the first axis of the channel Yes No
(V.)[n].TM.TOFLW2 Wear offset of the tool in the second axis of the channel Yes No
(V.)[n].TM.TOFLW3 Wear offset of the tool in the third axis of the channel Yes No
(V.)TM.TOFLWT[m][i].Xn Xn axis deviation wear of the [i] offset of the [m] tool Yes No
(V.)TM.TOR[i] Radius of active tool, offset [i].
(V.)TM.TOR Radius of active tool, active offset.
(V.)TM.TORT[m][i] Tool radius [m], offset [i].
(V.)TM.TORT[m] Tool radius [m], active offset in the channel.
"CUSTOM" DATA
PRG PLC INT
(V.)[n].TM.TOTP1 Additional parameter 1 of the active tool R/W R/W R/W
(V.)[n].TM.TOTP2 Additional parameter 2 of the active tool R/W R/W R/W
(V.)[n].TM.TOTP3 Additional parameter 3 of the active tool R/W R/W R/W
(V.)[n].TM.TOTP4 Additional parameter 4 of the active tool R/W R/W R/W
(V.)TM.TOTP1T[i] Additional parameter 1 of the [i] tool R/W R/W R/W
(V.)TM.TOTP2T[i] Additional parameter 2 of the [i] tool R/W R/W R/W
(V.)TM.TOTP3T[i] Additional parameter 3 of the [i] tool R/W R/W R/W
(V.)TM.TOTP4T[i] Additional parameter 4 of the [i] tool R/W R/W R/W
TOOL MANAGER
PRG PLC INT
(V.)[n].TM.MZSTATUS Status of the tool manager — R R
(V.)[n].TM.MZRUN Tool manager running — R R
(V.)[n].TM.MZMODE Operating mode of the tool manager R/W R R/W
(V.)[n].TM.MZWAIT Tool manager executing a maneuver R R R