background image

TECHNICAL DATA
OIL-HYDRAULIC OPERATOR

Opening time 
 

stroke 150 mm 

(P5): 10 s + Br.T.

 

stroke 280 mm 

(P3): 26 s + Br.T. 

(P5): 17 s + Br. T.

 

stroke 400 mm 

(P3): 37 s + Br.T. 

(P5): 26 s + Br.T. 

Piston 

diameter 

  45 

mm

Shaft 

diameter 

  20 

mm

Thrust power 

 

 

(P3): 0 ÷ 6.300 N    (P5): 0 ÷ 5.400 N

Average working pressure 

 

1 MPa (10 bar)

Maximum pressure  

 

3,5 MPa (35 atm)

Hydraulic oil 

 

 

Fadini Oil - code 708L

Working temperature 

 

- 25 °C + 80 °C

Protection 

grade 

  IP 

67

Weight complete with accessories 

9,5 kg (stroke 150 mm)

    11 

kg 

(stroke 

280 

mm)

    14 

kg 

(stroke 

400 

mm)

Br. T. = Braking Time, varies depending on the setting done on the operator

Note: beyond 2,0 meters of gate width, it is always recommended that a gate 
lock be fitted

.

ELECTRIC MOTOR

Power output 

 

0,18 kW (0,25 HP)

Absorbed power   

250 W

Supply voltage 

 

230 Vac - 50 Hz

Absorbed current   

1,2 A

Motor rotation speed 

1.350 rpm

Capacitor 

  12,5 

μF

Intermittent service 

S3

PERFORMANCE

Frequency of use   

very intensive

Duty cycle (P5) 

 

opening 17 s

   dwell 

30 

s

   closing 

21 

s

   dwell 

40 

s

Time of one complete cycle  108 s
Complete cycles 

 

n° 33/hour

Annual cycles
(8 hours per day)   

n° 81.760 cycles

universal oil-hydraulic operator for swing gates 

HINDI 880 - evo

English

24

Via Mantova, 177/A - 37053 Cerea (VR) Italy 
Ph. +39 0442 330422 

Fax +39 0442 331054

[email protected] - www.fadini.net

GB

2012/19/UE

 Directive

Re. disposal of electric

and electronic waste

DISPOSE PROPERLY OF MATERIALS

ARMFUL TO THE ENVIRONMENT

94

117

94

82

117 mm

92

80

L

15*

C

L0

L1

100

1

1,5

2

3

4

8

2,8

200

300

400

500

600

Stroke 150 mm

Stroke 280 mm

Stroke 400 mm

Stroke 400 mm*

*Special version

MAX GATE WIDTH PER LEAF (m)

MA

X GATE WEIGHT PER LEAF (k

g)

The gate structure, design (solid, in-filled), height and strong wind 
pressure may affect and decrease the indicated values. Make always 
sure the gate structure is adequate to automation.

C

 (actual stroke)    

L           L0* 

L1*

                  [mm]

145 

 

   830 

605 

   750

275  

1.094 

732 1.007

395  

1.374 

885 1.280

* these distances can vary depending

on the position of the ball bearing eye 

2018/07

istr_hindi880evo_GB.ai   12   18/06/2018   11:25:25

Summary of Contents for Hindi 880-Evo













Reviews: