fadini Hindi 880-Evo Instruction Manual Download Page 10

Page: 10 / 12

Tie-rods

Hindi 880-evo

Rear cap

fixing pin

Rear cap

Hindi 880-evo installed on the

right

view from inside the gate

Hindi 880-evo installed on the

left

view from inside the gate

Power cable

supplied with the

equipment

Cable gland to be inserted

in the previously created slit

Rear cap

Slit allowing the gland and power

supply cable to pass through it

Cover

front plug

Hexagonal grommet nuts:
use the supplied spanner
to remove them

Operator cover

Pic. 22

Pic. 23

FITTING THE REAR PROTECTION CAP AND COVER FIXING

NOTE WELL

The power supply electric cable is

ALWAYS

be positioned on the side opposite the rear fixing

plate, between the bolt and the operator end

casting.

universal oil-hydraulic operator for swing gates

HINDI 880 - evo

English

istr_hindi880evo_GB.ai 10 18/06/2018 11:25:24

Summary of Contents for Hindi 880-Evo













Search results

Summary of Contents for Hindi 880-Evo

Reviews:

Related manuals for Hindi 880-Evo

Brands by name

Popular brands

fadini Hindi 880-Evo, Instruction Manual

Search results

Summary of Contents for Hindi 880-Evo

Reviews:

Related manuals for Hindi 880-Evo

Brands by name

Popular brands