fadini Elpro S50-T4, Manual

Page: 11 / 24

3
DIP-SWITCH N° 3:
ON: Automatic closing
OFF: No automatic closing.
Semi-automatic mode
T3
DWELL TIME
1 s - 180 s
-
+
FUNCTIONS
The acoustic device is inside the post and
is on only during the rising and lowering
movements of the post.
Beeper, post in motion:
Board power supply:
Description Dip-switches and LED status of the various functions
7
DIP-SWITCH N° 7:
ON: Deadman control
OFF: Standard operating mode
Deadman control:
Open and Close operations are achieved “by holding a switch on” (no relay
self-holding is involved). Therefore, a physical attendance is required during
the entire cycle of movements until either the button or key is released.
Automatic / semiautomatic:
Automatic cycle: after a pulse to open, the bollard goes down, it stays stopped as long as the dwell
time lasts, as pre-set by T3 trimmer, and on expiring of such time it goes up automatically.
Semi-Automatic cycle: after a pulse to open, the bollard goes down.
Another pulse is needed to close the gateway.
3
DIP-SWITCH N° 3:
ON: Automatic closing
OFF: No automatic closing.
Semi-automatic operating mode
T3
DWELL TIME
1 s - 180 s
-
+
External time clock (optional):
CLOCK: the Elpro S50-T4 controller allows for a normal clock to be connected to it commanding the post
to rise and lower.
Connections: parallel connect the NO contact of the clock to the terminals No. 4 open and No. 3 common,
and set the controller to automatic mode by Dip-Switch n° 3 = ON.
How it works: set the clock to the required opening time. On the pre-set time the post is automatically
lowered ( the indication light emits 2 short flashes followed by a longer pause). Any further
command/pulsing (even by remote control) is not accepted by the system until the time pre-set on the
clock is expired. On expiring of it, and after the pre-set dwell time, the post rises
automatically.
DIP-SWITCHES N° 8 and N° 9:
Plug-in traffic lights card (optional):
The power supply of the traffic lights card is independent
from that of the electronic control board:
-
230 V - 50 Hz with an output of 100 W at 230 V ea. lamp.
- 24 V with an output of 25 W each lamp.
- 12 V with an output of 22 W each lamp.
Functioning applies also to traffic lights with 2 lamps, red
and green (Dip Switch 8 = OFF and 9 = OFF).
Functioning logic:
- GREEN Light= post down, gateway OPEN
- RED Light = post moving or standing,
gateway CLOSED
- YELLOW Light = it switches on before green turns
to red light.
8
OFF
9
OFF
8
ON
9
OFF
8 9
OFF
ON
8
ON
9
ON
Dip-Switch 8 = OFF and 9 = OFF
Yellow turns on for 0 s and after 0 s
red turns on and the post starts
rising immediately
Dip-Switch 8 = ON and 9 = OFF
Yellow turns on for 2 s , then red
turns on and after 2 s the post
starts rising
Dip-Switch 8 = OFF and 9 = ON
Yellow turns on for 6 s , then red
turns on and after 5 s the post
starts rising
Dip-Switch 8 = ON and 9 = ON
Yellow turns on for 10 s, then red
turns on and after 7 s the post
starts rising
RED
YELLOW
GREEN
Red
Yellow
Green
Fuse 1 A
( Optional: plug-in traffic lights
card at a 230 V, 24 V or 12 V).
Item Code No.
7282L
Red
Yellow
Green
Power supply 230 V - 50 Hz, 24 V or 12 V
Common
63 64 65 66 60 61
BEEPER or
LED
. C
OMMON
BEEPER
51 52 53
L1 N L2 L3
L N L L
!
JUMPER
L-L-L
BOARD POWER
SUPPLY 400 V ± 10%
50 Hz THREE-PHASE
BOARD POWER
SUPPLY 230 V ± 10%
50 Hz SINGLE-PHASE
GB
CONTROLLER FOR TALOS M50
ANTI-TERRORISM RETRACTABLE BOLLARDS
Elpro S50-T4
Accessory Electrical connections Dip-switches and LED status of the various functions
11