pag 21
Junior 624 - 24V dc
meccanica
FADINI
Elpro 62
GB
!
!
ADJUSTMENT OF STRENGTH:
The adjustment of the Force by the Trimmer must be necessary to move the gate. This adjustment also determines the
strength and impact resistance slowing down with an obstacle. A force too high inertia of the gate leads to incorrect
installation according to safety standards EN 12445 and EN 12453
Therefore, it requires the installer once adjusted the force applied to the gate operator to check the forces in play as
determined by the regulations EN12445 and EN12453 documented in the manual "Safety Standards" that the manufacturer
provides
FUNCTIONS: DESCRIPTION OF THE FUNCTIONS OF THE JUNIOR 624 SLIDING OPERATOR
Automatic / Semiautomatic:
Automatic Cyrcle
: upon open command impulse, the gate opens, stops in
pause for the time set in the Pause Trimmer, which, once passed will reclose
automatically.
Semiautomatic Cycle
: with an open command impulse the gate moves to
opening. To close the passage it is necessary to give the close command.
-
+
Pause Trimmer:
the pause time in the
automatic mode is adjusted to 120s
3
ON
: Close in automatic
OFF
: Semiautomatic
DIP-SWITCH 3:
Dip - Switch and LED signalling od different functions
Description
Reclose to passage above pair of photocelles:
Function that allowed automatic reclose after 3s from passage above pairs of
photocelles
9
ON
: Enables the automatic closing after the
pasage through the pair of photocells
OFF
: No automatic closing
DIP-SWITCH 9:
Check the photocelles before to leave:
Function that allowes the check of safety device like photocelles before to start
the movement of the gate.
A possible fault is signalled with the Amber coloured LED on the 10 casing
10
ON
: Enables safety systems check
OFF
: Disables safety systems check
DIP-SWITCH 10:
4
3
COMMON
COMMON
OPEN
NA
External clock
Opening by way of external clock:
Connection: connect the NA contact of the clock with terminal 4 OPEN and
terminal 3 COMMON in parallel, enabling the automatic closing with the Dip-
Switch 3=ON
Operation: program the opening time on the clock, at the time set the gate will
open and remain open ( the flasher goes off) and it will not accept other
commands (not even radio) until the times that has been set on the clock runs
out. Once that time has expired, after the pause time, the automatic closing
will follow.
3
ON
: Close in Automatic
Slow downs:
During programming it is recommended that the positions if initiate slow down
in opening and closing be set. Afterwards, these may be removed or recovered
by the way of the 6st Dip-Switch
The speed of the final run slow down of the gate is calibrated at the factory,
while the torque is proportional to the force exerted by the Junior by the way
of the
Trimmer Force:
adjust the torque applied by the gate
Trimmer Force:
adjust yhe torque applied
by the gate.
6
ON
: Eliminates slowdowns
OFF
: Activates slowdowns program
DIP-SWITCH 6:
-
+
ATTENTION: each variation or action on the Dip-switches for the functions, at any time, will be executed
at the moment of the next opening or closing command.
Trimmer Force:
adjust the torque applied
on the gate.
Beyond 3/4 of the adjustment it is possible
to obtain a greater force, wich does not
enable the gate to detect an obstacle
-
+
Reverse direction upon contact with obstacle:
Function that enables the inversion of the movement with contact with an
obstacle.
-
Opening phase:
the function reverses the direction for 10cm freeing the obstacle
-
Closing phase
: the function reverses the direction up to the limit switch
The sensitivity of the function is proportional to the forse exerted by the Junior
by the way of the
Trimmer Force
N.B. If the gate detects an obstacle 5 consecutive times during a complete
open-stop-close cycle, the gate will remain open and the lamp will flash
with a Blue light.
