page 13
meccanica
FADINI
GB
IN CASE OF FAILURE PLEASE MAKE SURE THAT
- Power supply to the electronic control box is 230V ±10%
- Power supply to the electric motor is 230V ±10%
- All of the fuses is all right
- The photocell contacts are closed
- No voltage drop has occurred from the Elpro board to the electric motor
- All of the NC contacts of the control board are all right
IMPORTANT FOR THE INSTALLATION AND THE CORRECT FUNCTIONING:
- The control box must be installed in a dry and sheltered place; suitable holes are provided with the FADINI universal box for fitting purpose and in
case any commercial box is used, this must be adequate to the job
- Make sure that power supply to the control board be 230V ±10%
- Make sure that power supply to the electric motor be 230V ±10%
- For distances longer than 50 metres increase the section of the wires
- Fit the mains to the control box with a high sensitivity, 0.03A, differential, magnetic-thermal circuit breaker
- Cables with 1.5mm² section wires are to be used for the power supply, electric motor and flasher for distances up to 50 m
- Cables with 1mm² section wires are to be used for the limit switches, photocells, push buttons and accessories
- If no photocells are used link out terminals 1 and 2
- If no stop button is used link out terminals 3 and 6
- Open/Close motor run time trimmer must be always superior to the time actually required for the gate travel
N.W.: For applications such as light switching, CCTV, etc. use solid state relays to prevent the microprocessor from being affected
Diagnostic LEDs:
L ON
= Board on 230V voltage and F1, F2, F3 fuses all right
L0 ON
= 2
nd
pair photocells, not obstructed
L1 ON
= 1
st
pair photocells not obstructed
L4 OFF
= Open, it switches on by any open pulse
L5
OFF
= Close, it switches on by any close pulse
L6
ON
= Stop, it switches off by any stop pulse
L7 OFF
= Radio, it switches on by any pulse from the transmitter/radio contact
L8 OFF
= Pedestrian mode, it switches on by any pedestrian pulsing
L10 ON
= Safety edge protecting closing
L30 ON
= It switches off when Fc.A. (limit switch Opening = L-sw.O) is engaged, M1
L31
ON
= It switches off when Fc.C. (limit switch Closing = L-sw.C) is engaged, M1
L33 ON
= It switches off when Fc.A. (limit switch Opening = L-sw.O) is engaged, M2
L34
ON
= It switches off when Fc.C. (limit switch Closing = L-sw.C) is engaged, M2
L35
ON
= Safety edge protecting opening
ATTENTION: before starting the electrical connections, select the mode of operation depending on gate type
by Dip Switch B N°1 and read the instructions respectively dedicated as follows:
SLIDING gates
from page 13 to page 18 -
SWINGING gates
from page 19 to page 23.
!
Symbols
NC
Contact
NO
Contact
Led
ON
Led
OFF
Pilot light
Flasher
27
UNIVERSAL ELECTRONIC CONTROL BOX
SINGLE-PHASE 230V 50/60Hz
General description:
the electronic control box ELPRO 27 has been developed to provide a reliable unit to control single or double sliding gate automatic
systems with or without limit switches, as well as single or double swinging gate systems fitted with pressure valves. S-phase 230V 50/60Hz ELPRO 27
complies with the Low Voltage Norms 2006/95 CE and Electro-magnetic Compatibility 2004/108/CE. Installation is recommended by qualified technical
installation agents in compliance with the existing regulations. The manufacturer is not liable for any incorrect use of this appliance; and also reserves
the right to change and update it without previous notice.
ELECTRIC MOTORS
230V SINGLE-PHASE
Power supply
350W max (0.5HP)
M1
M2
F3=2A
24V low
voltage circuit
protection
F2=5A
network
F1=5A
network
COURTESY LAMP
230V MAX 100W
It goes on when gate
starts and stays on for
a fixed time of 90
seconds
after motor
run time expiry
TRANSFORMER
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23
24
25
PLUG-IN
RADIO
CARD
CONNECTOR
2
nd
pair
photocells
NC
1
st
pair
photocells
radio contact
common
open
close
stop
Indication lamp 24V
max 3W
24V
ac output
(max
. load:
n°1 radio receiver
n°3 pairs photocells)
power supply for
electric lock
15V
A max
230Vac
OUTPUT
max 25W for flasher
and electric latch
Control board
power supply
230V - 50/60Hz ±10%
24V /ac output
for photocell TX
enabling
DS
A control
NC
common
common
NEUTRAL
LIVE
26
27
28
CARD
CONNECTOR FOR
TRAFFIC LIGHTS
(Item 7282L)
+
_
Power supply
24V - 50mA max.
DC
A
C
Selector
DC/AC
3 2 1
12V
24V
3
2
1
Pedestrian opening
LOCK
SETUP
Capacitor
M1 Motor
12.5 µF
Capacitor
M2 Motor
12.5 µF
F4=630mA
Transformer
primary
protection
OUTPUT CONFIGURATION
TERMINALS 14 - 15
UNL
ON
OFF
1 2 3 4 5 6 7 8 9 10 11 12
DIP-SWITCH - A
RUN
TIME
OPEN - CLOSE
sliding: 0s - 120s
swinging: 0s - 60s
DWELL
TIME
1s - 220s
-
GATE DELAY
CLOSING:
0s - 10s
- OPENING FOR
PEDESTRIANS 1s - 45s
-
+
-
+
-
+
ON
OFF
1 2 3 4
DIP-SWITCH - B
ELPRO 27
UNL
E 27
L4 L5 L6 L7 L8
L10
-
+
ELECTRIC LOCK
TIME
0.5s - 20s
L30 L31 L33 L34
30 31 32 33 34
M1
M2
Fc.A.
Fc.C.
Fc.A.
Fc.C.
35
L35
JA
1 2
SETUP
EDGE
TYPE
safety edge in closing
common
JB
1 2
Safety edge
in Opening
8,2 k or NC
8,2 k
or NC
Resistive contact
8,2 k or NC
L
L0
L1
NOTE:
The green LEDs must
always be on.
