ENTRIEGELUNG FÜR HANDBETRIEB
Abb. 11
Abb. 12
Abb. 13
Im Entriegelungsmodus führt der Antrieb keine Operation am Tor aus, trotz der Spannung, die weiterhin versorgt wird.
In dieser Situation kann das Tor manuell geöffnet und geschlossen werden, auch wenn der Antrieb noch darauf montiert ist.
Der gleiche codierte Schlüssel ermöglicht das Öffnen der Gleitschutzabdeckung und die manuelle Entriegelung (Abb. 11).
WICHTIG: Zur Wiederherstellung des Betriebs, führen Sie die beschriebenen Schritte in umgekehrter Reihenfolge durch.
Stecken Sie den Schlüssel
ein und drehen Sie ihn im
Uhrzeigersinn
Schieben Sie die Abdeckung nach vorne,
bis sie geöffnet ist
Drehen Sie den Schlüssel
gegen den Uhrzeigersinn,
dann entfernen und
stecken Sie ihn in den
Entriegelungssitz
Drehen Sie den Schlüssel
im Uhrzeigersinn bis zum
Anschlag
Lösen Sie die Schraube und stellen Sie
die Position der Anschlaggruppe
(innere und äußere Platte) ein, um die
vordere Torbefestigung zu berühren.
Die Platten müssen an den jeweiligen
Zahnstangen fest haften. Ziehen Sie
die Schraube fest an.
Lösen Sie die Schraube und stellen
Sie die Position der Anschlaggruppe
(innere und äußere Platte) ein, um
die vordere Torbefestigung zu
berühren. Die Platten müssen an
den jeweiligen Zahnstangen fest
haften. Ziehen Sie die Schraube fest
an.
Torflügel
ganz AUF
Torflügel
ganz ZU
2)
1)
Befestigungswinkel
am Tor
180° - Eine halbe
Drehung
FADINI
4)
FADINI
FADINI
FADINI
3)
FADINI
FADINI
elektromechanischer Drehtorantrieb
DARDO 430
DARDO 430
Deutsch
50
EINSTELLUNG DER MECHANISCHEN ANSCHLAGPLATTEN (für Anlagen ohne Bodenanschläge)
Entriegeln Sie den Antrieb (siehe Abb. 11) und öffnen Sie dann das Tor von Hand bis in die gewünschte Position: Lösen Sie die
Schraube, die die Anschlaggruppe festhält und positionieren die Platten, so dass die vordere Befestigung die Anschlagplatte
(Stopp) in der erforderlichen Öffnung berührt, dann die Schraube wieder festziehen (Abb. 12): Die äußere Anschlagplatte und ihr
Gegenstück, dh. Die innere Platte, müssen fest an den Zahnstangen haften. Führen Sie die gleichen Schritte mit dem Tor in
geschlossener Position durch (Abb. 13).
WICHTIG: Endlich setzen Sie den Antrieb zurück, um es am Torflügel wieder zu
blockieren (Schritte in Abb. 11 in umgekehrter Reihenfolge).
Befestigungswinkel am Tor
Summary of Contents for DARDO 430
Page 13: ...apricancello elettromeccanico per cancelli a battente DARDO 430 DARDO 430 Italiano 13 ...
Page 27: ...electromechanical operator for swinging gates DARDO 430 DARDO 430 English 27 ...
Page 41: ...automatisme électromécanique pour portails à battant DARDO 430 DARDO 430 Français 41 ...
Page 55: ...elektromechanischer Drehtorantrieb DARDO 430 DARDO 430 Deutsch 55 ...