background image

14

2.6 MAINTENANCE SPACE

During installation of the machine, it is advisable to set up an area for later maintenance operations, as indicated 

in fig. 8.

IMPORTANT: the values in the tables are the recommended minimum values. 

2.7 ELECTRIC PLUG-IN

WARNING! 

Before plugging in, make sure you have a proper grounding system which follows the current 

European Laws (EN).

Check the compatibility of the network voltage with the specificatins in the appropriate label 

in the machine (fig. 2).

Power fluctuations greater than ±10% of the nominal voltage indicated in the label can cause 

serious damage on the machine. That damage in not covered by the warranty.  

IMPORTANT: verify that the power cable is the right size.

Turn  the  switch  on  the  0  position  in  the  F85  CV-F120-F240  models  (pos. A  fig.11),  in  the  F85  (pos. A 

fig.11B). 

Insert the machine’s power cable through the gland under the power grid (pos. B fig.7). Connect wires in the 

terminal by following the attached electric plan (TAV. 2) and following. 

IF THE MACHINE HAS THE FUMES VENT:

Plug the fumes suction grid’s cable (pos. C fig.7).

Once the cable has been plugged, the suction vents’ orientation should be checked.

In the F85 CV-F120-F240 models, proceed as follows:

- Turn on the manual operation of the vents’ thermostat (press the white button) (fig.9);

- Turn on the general switch (fig.10);

The values in the table are expressed in mm.

F28

F55

F85

F120

F240

F350

 

1000  600    600   1500 

 1000   600   600   1500 

 1000  600    600  1500 

 1200  600    600  1800 

 1200  600   600  1800 

 1200  600    600   2000 

 

A    B 

 C 

A

B

D

C

FIG.8

Summary of Contents for F120




































Reviews: