E145S 27
532369 - Rev.A
Tr
ansla
tion of the orig
inal instruc
tions
ENGLISH
release it when the corresponding RADIO Led
(
RADIO1
or
RADIO2
) starts to flash for 20 s (time
available for the next steps).
2. Press buttons
P1
and
P2
simultaneously on the
radio control and release them when its LED starts
to flash for 8 s (time available for the next step).
3. Press and release the button on the radio control
to be memorised. The corresponding RADIO LED
on the board becomes steady for 1 s, then switches
off (memorisation complete).
4. Release the button.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
■
Adding radio controls
1. Press buttons
P1
and
P2
simultaneously on the
already memorised MASTER radio control and
release them when its LED starts to flash for 8 s
(time available for the next step).
2. Within 8 seconds, press and hold the button that
has already been memorised, the LED lights up
with a steady light.
3. Bring the radio control that has already been
memorised, into contact face to face with the new
one to be memorised.
4. Press the button to be memorised on the new radio
control and make sure that its LED flashes twice
before turning off.
5. Release all buttons.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
RADIO CONTROLS - RC/LC
■
Memorizing radio controls
1. On the board, press the
++
button (memorize OPEN
A) or the
--
button (memorize OPEN B/CLOSE) and
release it when the corresponding RADIO Led
(
RADIO1
or
RADIO2
) starts to flash for 20 s (time
available for the next steps).
2. Press and release the button on the radio control
to be memorised. The corresponding RADIO LED
on the board becomes steady for 2 s (memorisation
completed), then starts to flash again. Another
radio control can be memorised within 20 s.
The procedure ends after 20 s if no further radio
controls are memorised and the RADIO LED switches
off. To add additional radio controls, repeat the pro-
cedure from step 1.
■
Adding radio controls remotely
Use a LC/RC radio control that is already use by the
automation, without having to use the board.
1. Take a radio control that is already in use and move
close to the board.
2. Press buttons
P1
and
P2
simultaneously on the
radio control that is already in use and release
them when its LED starts to flash slowly for 5 s
(time available for the next step).
3. Press and release the button that has already been
memorized (the corresponding RADIO LED on the
board starts to flash for 20 s, the time available for
the next step).
4. Press the button to be memorised on the new
radio control (the corresponding RADIO LED on
the board
becomes steady for 2 s to confirm the
memorization. It then starts to flash again and an-
other radio control can be memorised within 20 s).
The procedure ends after 20 s if no further radio con-
trols are memorised (the corresponding RADIO LED
switches off). To add additional radio controls, repeat
the procedure from step 1.
RADIO CONTROLS - DS
1. Set the required combination of the DIP switches
on the radio control (avoid setting them to all On
or all Off).
2. On the board, press the
++
button (memorize OPEN
A) or the
--
button (memorize OPEN B/CLOSE) and
release it when the corresponding RADIO Led
(
RADIO1
or
RADIO2
) starts to flash for 20 s (time
available for the next step).
3. Press and release the button on the radio control
to be memorised. The corresponding RADIO LED
on the board becomes steady for 1 s and then
switches off (memorisation complete).
4. To memorize other radio controls, it is possible
to set a DIP switch combination that has already
been memorised or repeat the procedure for new
combinations.
DELETING RADIO CONTROLS
!
This procedure cannot be reversed. It will delete ALL
radio control codes that have been memorised as
OPEN A and
OPEN B/CLOSE
. The deletion procedure
is only active in the automation status display mode
1. Press the
--
button and do not release it until the
LED sequence has finished:
-
after 5 s the
RADIO2 LED
starts flashing slowly
-
after 5 s the
RADIO1
and RADIO2 LEDS both start to
flash quickly (deletion in progress)
-
after 5 s both the LEDs come on steadily (deletion
complete)
2. Release the button, both LEDs switch off after
approximately 10 s.
Summary of Contents for E145S
Page 1: ...E145S...
