EYELA SD-1010 Instruction Manual Download Page 37

Page: 37 / 47

2) Remove the evaporating tube from the main unit

evaporating tube installation part.

*Remove the outlet temperature sensor beforehand

from the sensor installation port on the branched
tube of the evaporating tube.

3) Disassemble and wash respective parts as

illustrated in the right figure.

*Use a neutral detergent to wash glass parts.

If they are dirty, immerse them in a neutral

detergent-diluted solution for about half a day
before washing them.

4) Assemble parts by reversing procedure.

Evaporating tube
mounting portion

Evaporator

Evaporating tube
receiving cradle

③

Pull out

②

Rotate

Rectification board

Evaporator

Cyclone

Separable seal packing

Packing (SC)

Connecting tube

Separable clamp (

75)

Code No.

Part name

Remarks

180370

Rectification board

180000

Evaporator

147840

Upper connection packing

146760

Collecting flask cap

199050

Lower connecting packing

146750

Separator, powder
collection container

116510

Separable clamp (

75)

180020

Connecting tube

116530

Separable seal packing

180010

Cyclone

180190

Packing (SC)

-32-

①

Loosen

Upper connecting packing

Powder collection container

Separator

Lower
connecting
packing

Collecting flask
Cap

Summary of Contents for SD-1010
















































Search results

Summary of Contents for SD-1010

Reviews:

Related manuals for SD-1010

Brands by name

Popular brands

EYELA SD-1010, Instruction Manual

Search results

Summary of Contents for SD-1010

Reviews:

Related manuals for SD-1010

Brands by name

Popular brands