background image

5-1-6 Attaching silicone tubing

1) After raising the lever, pull up the tube retainer 

immediately above and remove it from the 
sample delivery pump main.

Use a proper tubing.

Use the tubing diameter and material 
designated by our company for the tubing 
used to deliver a solution.
The use of non-designated tubing may cause 
degradation of performance or trouble.

Caution

Do not press the pressure sensor too 
much or do not pour water on it.

Applying unreasonable force to the pressure 
sensor main or cable or pouring water on it 
may result in failure of the pressure sensor.

Caution

Tube retainer

Lever

Delivery pump main

Length reaching sample 
container

Length reaching pressure sensor 
(approx. 100 mm)

Pull

Pull

Pressure sensor

Spray nozzle

Silicon tube
(ID3.7 x OD6.1 mm)

-14-

Code No.

Part name

Qty.

125510

Silicon tube 3.15 x 5.2

5m

125530

Silicon tube 3.7×6.1

5m

2) Set silicon cut in an appropriate length on the 

delivery pump main and fix the tube retainer.

3) Push down the lever of tube retainer and fixate the 

tube.

4) Slightly pull the base of tube to bring it out about 2 

mm.

5) Connect one side of silicon tube to the pressure 

sensor.

6) Joint the pressure sensor and spray nozzle with 

silicon tube cut in an appropriate length.

*Set the silicon tube (supplied with the product) 

"3.15

×

5.2 [mm] (ID

×

OD)" with the delivery 

pump.

[Tube used]

*Use a silicon tube (supplied with the product) in 

"3.7

×

6.1 [mm] (ID

×

OD)" between the pressure 

sensor and spray nozzle.

Summary of Contents for SD-1010
















































Reviews: