EYELA SD-1010 Instruction Manual Download Page 23 | Manualshive

Page: 23 / 47

background image

5-1-12 Installing agitator

A small agitator (SPZ-2000) can be installed by using

an agitator installation pole (option).(

Agitation from above allows delivery of solution

without grinding crystals.

1) Slightly loosen the decorative screw to make the

screw cover movable.

2) Rotate the screw cover until the pole installation

screw is completely visible, fasten the decorative
screw to secure the cover.

3) Tighten the agitator installation pole on the pole

installation screw.

4) Mount the agitator drive on the agitator installation

pole.

5) Place the agitator operating portion on the upper

part of the main.

*See and follow the Installation Manual of the small

agitator (SPZ-2000) when using it.

Code No.

Part name

Remarks

275200

Agitator installation
pole

124560

ZC clamp

260530

Small agitator

SPZ-

2000

Agitator pole

Pole fixing screw

-18-

ZC clamp

Agitator drive

Agitator operating portion

Agitator pole

②

Install

Decorative screw

Screw cover

①

Rotate

«
...
21
22
23
24
25
...
»

Summary of Contents for SD-1010
















































Reviews:

No comments

Related manuals for SD-1010

Brand: UFESA Pages: 62

Brand: T-Fal Pages: 19

EZ CLEAN INOX & DESIGN

Brand: T-Fal Pages: 29

Brand: AYA Pages: 21

Brand: Daewoo Pages: 12

FreeZone 74200 Series

Brand: Labconco Pages: 65

Brand: S&P Pages: 20

Centauro CLGG70214 Series

Brand: mabe Pages: 138

MF200D80WB Series

Brand: Midea Pages: 44

Brand: Vitek Pages: 20

Brand: Modena Pages: 20

Brand: LG Pages: 48

Brand: LG Pages: 76

Brand: LG Pages: 48

Brand: LG Pages: 44

Brand: APRILIA Pages: 16

Brand: Motak Pages: 20

Brand: Brandt Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands