Extron electronics MultiMatrix SMX System Setup Manual Download Page 12

Page: 12 / 48

SMX System MultiMatrix Switcher • Front Panel Operation

Front Panel Operation

This section details the physical configuration and front panel
operation of the SMX after the installation process and includes:

•

Front Panel Overview

•

Creating Ties

•

Viewing Ties

•

Muting or Unmuting Outputs

•

Removing Ties

•

Saving and Recalling I/O Presets

•

Adjusting the Input Audio Level

•

Adjusting the Output Audio Volume

•

Using Reset Levels

•

Setting the Front Panel Locks (Executive Modes)

Front Panel Overview

SMX SERIES SWITCHER

I/O PLANE SELECT

INPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUTPUTS

CONTROL

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

ENTER

PRESET

VIEW

ESC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

MAIN

I/O CARDS

CONFIG

Figure 6.

Front Panel Features

I/O Plane address selection buttons

—

Select I/O planes (0-15), and

buttons 0 and 1 select RS-232 or RS-422 communication.

Input selection buttons

—

Select inputs, create and remove ties,

sets background illumination (press and hold inputs 0 and 1), or
indicate output audio volume.

Output selection buttons — Select outputs, create and remove

ties, and indicate input audio gain/attenuation.

NOTE:

Input buttons are can also be used to save and recall

global and plane presets.

Control buttons — Enter, Preset, View, and Esc. Used to configure

unit; save and recall presets; create, remove, and view ties; adjust
audio volume and gain; switch lock modes; configure ports; and
reset the SMX.

Summary of Contents for MultiMatrix SMX System

















































Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands

Extron electronics MultiMatrix SMX System, Setup Manual

Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands