Extron electronics MultiMatrix SMX System Setup Manual Download Page 39

Page: 39 / 48

SMX System MultiMatrix Switcher • Control and Configuration

Click the

Software

tab.

Scroll to the SMX Control Program and click

Install

Follow the on-screen instructions. The installation program creates
a

C:\Program Files\Extron\SMX

folder with 3 icons for the

SMX Control pgm, SMX Help, and Uninstall SMX Control pgm.

Starting the Program

Click

Start > Programs > Extron Electronics

> SMX Control Program > SMX Control Pgm

The Comm Port Selection window appears.

Figure 24.

Comm Port Selection Window

Choose the comm (serial) port connected to the SMX or IP [LAN].

NOTE:

For a comm port, check the baud rate displayed in the

Comm Port Selection

window. To change the baud

rate, click the

Baud

button, select the desired baud

rate.

Click

If you select

IP [LAN]

, the IP Connection window appears.

Figure 25.

IP Connection Window

Summary of Contents for MultiMatrix SMX System

















































Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands

Extron electronics MultiMatrix SMX System, Setup Manual

Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands