Extron electronics MultiMatrix SMX System Setup Manual Download Page 19

Page: 19 / 48

SMX System MultiMatrix Switcher • Front Panel Operation

Input Audio Level Table

Color

Output Buttons Lit

or Flashing

+/-

Color Output Buttons Lit

or Flashing

+/-

green

-01

red

1 flash

green

12 flash

-02

red

1 flash

green

-03

red

2 flash

green

11 flash

-04

red

2 flash

green

-05

red

3 flash

green

10 flash

-06

red

3 flash

green

-07

red

4 flash

green

9 flash

-08

red

4 flash

green

-09

red

5 flash

green

8 flash

-10

red

5 flash

green

-11

red

6 flash

green

7 flash

-12

red

6 flash

green

-13

red

7 flash

green

6 flash

-14

red

7 flash

green

-15

red

8 flash

green

5 flash

-16

red

8 flash

green

-17

red

9 flash

green

4 flash

-18

red

green

= Esc

= View

green

3 flash

green

2 flash

green

1 flash

Not lit

NOTES:

•

There is only one audio level setting per input and
one per output on an audio plane. The audio level
and volume is shared by the left and right inputs and
outputs.

•

Audio levels and volumes are stored in nonvolatile
memory. When power is removed or restored, settings
are retained.

Summary of Contents for MultiMatrix SMX System

















































Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands

Extron electronics MultiMatrix SMX System, Setup Manual

Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands