Extron electronics MultiMatrix SMX System Setup Manual Download Page 31

Page: 31 / 48

SMX System MultiMatrix Switcher • SIS Programming Guide

Command

ASCII Command

(host to switcher)

Response

(switcher to host)

Additional Description

Plane Pr

esets

Save current ties as a plane

preset

X2@

X1!

*0,

X2@

Spr

X1!

]

Save the current set of ties as plane

preset

X1!

. The command character

is a comma (

Recall a plane preset

X2@

X1!

*0.

X2@

Rpr

X1!

]

Recall plane preset

X1!

, which

becomes the current configuration.

The command character is a period

(

irtual (Multi Plane) Definition

rite virtual plane address

X2(

X2@

...

X2@

}

Mpv

X2(

X2@

...

X2@

]

rite virtual plane addresses .

Read virtual plane address

X2(

}

X2@

...

X2@

]

Read virtual plane address.

ont Panel Lockout (Executive Mode)

Lock front panel (advanced

functions)

Exe2

]

Enable advanced executive mode.

Lock front panel (advanced and

basic functions)

Exe1

]

Enable executive mode.

Unlock front panel

Exe0

]

Disable executive mode.

iew front panel lock status

]

= status of executive mode.

NOTE:

For full lock mode details, refer to

Setting the Fr

ont Panel Locks (Executive Modes)

on page 18.

NOTES:

= Executive mode:

= unlocked (all functions),

= locked (basic and advanced),

= locked (advanced, default value)

X1!

= Preset number

for global presets,

for plane presets

X2@

= Plane number

X2(

= V

irtual plane number

Summary of Contents for MultiMatrix SMX System

















































Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands

Extron electronics MultiMatrix SMX System, Setup Manual

Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands