Extron electronics MultiMatrix SMX System Setup Manual Download Page 41 | Manualshive

Page: 41 / 48

background image

35

SMX System MultiMatrix Switcher • Control and Configuration

Using the Web Pages to Configure the SMX

The SMX settings can be configured via LAN or WAN web pages using
a suitable Internet browser (Internet Explorer, Firefox

®

).

To view and configure the SMX via web pages:

1.

If not already done, connect the SMX to a PC using the rear panel
RJ-45 LAN connector.

2.

Open the Internet browser on the host computer, and in the
address bar, type the IP address for the SMX .

NOTE:

The default IP address is 192.168.254.254. Check with

the administrator if the IP address has been changed.

3.

The browser opens the SMX default web page (see

), at

the System Status page.

Figure 26.

SMX Default Web Page

—

System Status

There are three other pages: the Configuration page, the
File Management page, and the Control page. Any of these pages
can be accessed by clicking on the applicable tab.
Click in the left column to access related subsections of each page.

Status Page

This page allows the user to monitor the system. Settings shown are
not configurable from this page. The page may include subsections
such as System Status, Physical Configuration, and DSVP.

«
...
39
40
41
42
43
...
»

Summary of Contents for MultiMatrix SMX System

















































Reviews:

No comments

Related manuals for MultiMatrix SMX System

Brand: N-Tron Pages: 20

Brand: CALIENT Pages: 46

Brand: CALIENT Pages: 42

Brand: X10 Pages: 20

Brand: DITEC Pages: 8

SwitchView SC8 DVI

Brand: Avocent Pages: 2

Brand: Hall Technologies Pages: 35

OmniView Secure F1DN102Uea

Brand: Belkin Pages: 36

EXHL-TRN-LE1 Series

Brand: Larson Electronics Pages: 2

SISTG1040-242-LRT

Brand: Transition Networks Pages: 31

Brand: Fairchild Pages: 20

Brand: Orei Pages: 27

Brand: Stahl Pages: 29

Enova DGX 100 Series

Brand: AMX Pages: 2

Brand: Emulex Pages: 75

Brand: SMART-AVI Pages: 2

Brand: odot Pages: 15

Brand: CTC Union Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands