Extron electronics MultiMatrix SMX System Setup Manual Download Page 16

Page: 16 / 48

SMX System MultiMatrix Switcher • Front Panel Operation

Saving and Recalling I/O Presets

Save current configurations as global or plane presets to save audio
and video ties. The SMX has 32 global preset (using I/O buttons 1-16)
and 10 plane presets (input buttons 1-10) addresses available.

Global preset

—

Saves and recalls configurations for all planes (see

figure 14

for global preset addresses).

Plane preset

—

Saves and recalls the configurations for a specific

plane without affecting the other plane connections (see

figure 14

for plane preset addresses).

NOTES:

•

Presets cannot be viewed from the front panel unless
recalled as the current configuration (see the User
Guide for ways to view presets).

•

The current configuration and all presets are retained
when power is removed and then restored.

•

Recalled presets override current configurations.

•

Audio gain settings are not saved with presets.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

INPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUTPUTS

GLOBAL

PLANE

GLOBAL

Preset

Figure 14.

Global and Plane Preset Addresses

Saving or Recalling a Global Preset

Press the Esc button to clear any pending changes. The button
flashes once.

Perform one of the following:

ENTER

INPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUTPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

C O N T R O L

PRESET

ESC

VIEW

Figure 15.

Saved Global Presets 8, 18, and 32

—

an Example

•

save

a global preset, press and

hold

the Preset button for

2 seconds. The Preset button flashes red.

•

recall

a global preset, press and

release

the Preset button.

The Preset button lights red.

Summary of Contents for MultiMatrix SMX System

















































Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands

Extron electronics MultiMatrix SMX System, Setup Manual

Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands