Extron electronics MultiMatrix SMX System Setup Manual Download Page 20 | Manualshive

Page: 20 / 48

background image

14

SMX System MultiMatrix Switcher • Front Panel Operation

Adjusting the Output Audio Volume

The audio output level of each output can be displayed and adjusted
through a range of 64 steps (1 dB per step, 0% to 100%). The audio
level can be adjusted from the front panel, RS-232, RS-422, or through
Ethernet. Adjustment is attenuation only.

NOTES:

•

Refer to the

SMX User Guide

for other adjustment

methods.

•

Front panel adjustment and viewing are only available
when the unit is in Lock mode 0.

1.

Press the Esc button to clear any pending changes. The button
flashes green once.

2.

Press the desired audio I/O Plane button to be adjusted. The plane
button and Input 1 light.

I/O PLANE SELECT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

0

Figure 20.

Plane 4 Selected

—

an Example

3.

Press and

hold

any Ouput button until the I/O Plane button

flashes. I/O buttons turn off.

4.

Press the button for the output that needs the audio volume
adjusted. The selected output button lights green. The current
audio volume is indicated by the lit and flashing Input buttons
(see the

Output Audio Volume Table

on page 15 for lighting and

volume levels).

INPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUTPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Figure 21.

Output 3 Set to 100% Audio Volume

—

an Example

5.

Press and

hold

the

View

button to decrease or the

Esc

button

to increase audio level. The selected output button remains lit.
Inputs light, flash, or go out as the volume changes.

INPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUTPUTS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Figure 22.

Output 3 Set to 67.0% Audio Volume

—

an Example

6.

Press the Enter button to leave the output audio volume
adjustment mode. All button lights turn off.

«
...
18
19
20
21
22
...
»

Summary of Contents for MultiMatrix SMX System

















































Reviews:

No comments

Related manuals for MultiMatrix SMX System

Switch 4500 Family

Brand: 3Com Pages: 16

PathBuilder S200 Series

Brand: 3Com Pages: 32

Brand: Eaton Pages: 12

Brand: Patton electronics Pages: 104

Brand: Xantech Pages: 20

Brand: Hansen Pages: 4

Brand: Techroutes Pages: 22

Brand: ADDER Pages: 46

Sierra Pro XL 1616V3

Brand: Kramer Pages: 2

Brand: Kohler Pages: 170

Brand: FS Pages: 41

Brand: HIKVISION Pages: 5

Brand: Nobile Pages: 2

LMP-0602 24-V2 Series

Brand: ANTAIRA Pages: 2

Brand: Key Digital Pages: 20

Brand: Edimax Pages: 8

Brand: Inline Pages: 4

Brand: Lindy Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands